- ページ 12

レンジ KitchenAid YKFED500ESSのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid YKFED500ESS 16 ページ。 30" (76.2 cm) freestanding electric range with double ovens

ページを印刷する

3. Use ³⁄₈" nut driver to connect the bare (green) ground wire to

the center terminal block post with one of the 10-32 hex nuts.

A. 10-32 hex nut

B. Line 1 (black)

C. Ground-link screw

4. Connect line 1 (black) and line 2 (red) wires to the outer

terminal block posts with 10-32 hex nuts.

5. Securely tighten hex nuts.

6. Replace terminal block access cover.

7. Slide range back so rear range foot is under the anti-tip

bracket. See the "Verify Anti-Tip Bracket is Installed and

Engaged" section.

Verify Anti-Tip Bracket Is Installed

and Engaged

1. Place the outside of your foot against the bottom front of the

oven door to keep the range from moving, and grasp the

lower right-hand or left-hand side of the control panel as

shown.

NOTE: If your countertop is mounted with a backsplash, it

may be necessary to grasp the range higher than is shown in

the illustration.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than ½" (1.3 cm) off the floor

without resistance, stop tilting the range and lower it gently

back to the floor. The range foot is not engaged in the anti-tip

bracket.

IMPORTANT: If there is a snapping or popping sound when lifting

the range, the range may not be fully engaged in the bracket.

Check to see if there are obstructions keeping the range from

sliding to the wall or keeping the range foot from sliding into the

bracket. Verify that the bracket is held securely in place by the

mounting screws.

D. Bare (green) ground wire

E. Line 2 (red)

F. Terminal lug

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. If you

need assistance or service, refer to the "Assistance or Service"

section of the Use and Care Guide, or the cover or "Warranty"

section of the User Instructions, for contact information.

6. Repeat steps 1 and 2 to ensure that the range foot is

engaged in the anti-tip bracket.

If the rear of the range lifts more than ½" (1.3 cm) off the floor

without resistance, the anti-tip bracket may not be installed

correctly. Do not operate the range without anti-tip bracket

installed and engaged. Please reference the "Assistance or

Service" section of the Use and Care Guide, or the cover or

"Warranty" section of the User Instructions, to contact service.

Level Range

1. Place a rack in oven.

2. Place level on rack and check levelness of range, first side to

side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

4. Use a wrench or pliers to adjust leveling legs up or down until

the range is level. Push range back into position.

5. Check that rear leveling leg is engaged in the anti-tip bracket.

NOTE: Range must be level for satisfactory baking

performance.

Complete Installation

1. Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials.

4. Check that the range is level. See the "Level Range" section.

5. Use a mild solution of liquid household cleaner and warm

water to remove waxy residue caused by shipping material.

Dry thoroughly with a soft cloth. For more information, read

the "Range Care" section of the Use and Care Guide.

6. Read the range Use and Care Guide.

7. Plug power cord into appropriate outlet. Slide range into its

final location. Check that the flexible conduit or power supply

cord is bent.

8. Turn power on. Turn on surface elements and oven. See the

Use and Care Guide for specific instruction on range

operation.

If range does not operate, check the following:

■

Household fuse is intact and tight; or circuit breaker has not

tripped.

■

Range is plugged into a grounded outlet.

■

Electrical supply is connected.

■

See the "Troubleshooting" section in the Use and Care Guide.

When the range has been on for 5 minutes, check for heat. If

range is cold, turn off the range and contact a qualified

technician.