- ページ 4

レンジ KitchenAid YKFED500ESSのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid YKFED500ESS 16 ページ。 30" (76.2 cm) freestanding electric range with double ovens

ページを印刷する

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrical installer determine that

the ground path and wire gauge are in accordance with local

codes.

Do not use an extension cord.

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/

NFPA 70-latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

WARNING: Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check with a

qualified electrician or service technician if you are in doubt as to

whether the appliance is properly grounded. Do not modify the

power supply cord plug. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

Electrical Connection

To properly install your range, you must determine the type of

electrical connection you will be using and follow the instructions

provided for it here.

■

Range must be connected to the proper electrical voltage

and frequency as specified on the model/serial/rating plate.

The model/serial/rating plate is located behind the control

panel. Refer to the figures in "Product Dimensions" in the

"Location Requirements" section.

■

This range is manufactured with the neutral terminal

connected to the cabinet. Use a 3-wire, UL listed, 40- or

50-amp power supply cord (pigtail) (see the following Range

Rating chart). If local codes do not permit ground through the

neutral, use a 4-wire power supply cord rated at 250 volts,

40- or 50-amps and investigated for use with ranges.

Range Rating*

120/240 Volts

120/208 Volts

8.8 - 16.5 KW

7.8 - 12.5 KW

16.6 - 22.5 KW

12.6 - 18.5 KW

*The NEC calculated load is less than the total connected load

listed on the model/serial/rating plate.

**If connecting to a 50-amp circuit, use a 50-amp rated cord with

kit. For 50-amp rated cord kits, use kits that specify use with a

nominal 1³⁄₈" (34.9 mm) diameter connection opening.

■

A circuit breaker is recommended.

■

The range can be connected directly to the circuit breaker

box (or fused disconnect) through flexible or nonmetallic

sheathed, copper or aluminum cable. See the "Electrical

Connection - U.S.A. Only" section.

■

Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack in the line so that

the range can be moved if servicing is ever necessary.

■

A UL listed conduit connector must be provided at each end

of the power supply cable (at the range and at the junction

box).

■

Wire sizes and connections must conform with the rating of

the range.

■

The wiring diagram is located on the Tech Sheet.

■

The Tech Sheet is located on the back of the range inside a

clear plastic bag.

Electrical Requirements

Specified Rating of

Power Supply Cord Kit

and Circuit Protection

Amps

40 or 50**

If connecting to a 4-wire system:

This range is manufactured with the ground connected to the

neutral by a link. The ground must be revised so the green

ground wire of the 4-wire power supply cord is connected to the

cabinet. See "Electrical Connection - U.S.A. Only" section.

Grounding through the neutral conductor is prohibited for new

branch-circuit installations (1996 NEC); mobile homes; and

recreational vehicles, or an area where local codes prohibit

grounding through the neutral conductor.

When a 4-wire receptacle of NEMA Type 14-50R is used, a

matching UL listed, 4-wire, 250-volt, 40- or 50-amp, range power

supply cord (pigtail) must be used. This cord contains 4 copper

conductors with ring terminals or open-end spade terminals with

upturned ends, terminating in a NEMA Type 14-50P plug on the

supply end.

The fourth (grounding) conductor must be identified by a green or

green/yellow cover and the neutral conductor by a white cover.

Cord should be Type SRD or SRDT with a UL listed strain relief

and be at least 4 ft (1.22 m) long.

4-wire receptacle (14-50R)

The minimum conductor sized for the copper 4-wire power

cord are:

40-amp circuit

2 No.-8 conductors

1 No.-10 white neutral

1 No.-10 green grounding

If connecting to a 3-wire system:

Local codes may permit the use of a UL listed, 3-wire, 250-volt,

40- or 50-amp range power supply cord (pigtail). This cord

contains 3 copper conductors with ring terminals or open-end

spade terminals with upturned ends, terminating in a NEMA Type

10-50P plug on the supply end. Connectors on the appliance end

must be provided at the point the power supply cord enters the

appliance. This uses a 3-wire receptacle of NEMA Type 10-50R.

3-wire receptacle (10-50R)