- ページ 6

レンジ KitchenAid YKFEG500ESSのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。KitchenAid YKFEG500ESS 20 ページ。 Freestanding
KitchenAid YKFEG500ESS にも：クイック・スタート・マニュアル (2 ページ), オーナーズマニュアル (18 ページ)

ページを印刷する

8. Move range forward onto shipping base, cardboard or

hardboard to continue installing the range using the following

installation instructions.

WARNING

Electrical Shock Hazard

Electrically ground range.

Failure to do so can result in death, fire, or

electrical shock.

9. Plug power cord into a grounded outlet (see "Electrical

Requirements" section).

10. Slide range back so that rear range foot is engaged in the

anti-tip bracket slot.

Level Range

Determine if you have AquaLift

referring to the "Range Care" section of the User Instructions.

For Ranges with AquaLift

1. Place level on the oven bottom as indicated in one of the two

figures below, depending on the size of the level. Check with

the level: side to side and front to back.

2. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

3. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

For Ranges without AquaLift

1. Place a standard flat rack in oven.

2. Place level on the rack and check levelness of the range, first

side to side; then front to back.

3. If range is not level, pull range forward until rear leveling leg is

removed from the anti-tip bracket.

4. Follow the directions in Style 1 or Style 2, depending on the

style of drawer supplied with the range.

Style 1: Ranges Equipped with a Storage Drawer:

Use a ¼" drive ratchet, wrench or pliers to adjust leveling legs

up or down until the range is level. Push range back into

position. Check that rear leveling leg is engaged in the anti-tip

bracket.

†® AQUALIFT is a registered trademark of Whirlpool, U.S.A.

®†

Technology or Steam Clean by

Technology or Steam Clean:

Style 2: Ranges Equipped with a Warming Drawer or

Premium Storage Drawer:

Use a wrench or pliers to adjust leveling legs up or down until

the range is level. Push range back into position. Check that

rear leveling leg is engaged in the anti-tip bracket.

5. NOTE: Range must be level for satisfactory baking

performance and best cleaning results using AquaLift

Technology and Steam Clean functions.

Verify Anti-Tip Bracket Is Installed and

Engaged

On Ranges Equipped with a Storage Drawer:

1. Remove the storage drawer. See "Storage Drawer" section.

2. Use a flashlight to look underneath the bottom of the range.

3. Visually check that the rear range foot is inserted into the slot

of the anti-tip bracket.

On Ranges Equipped with a Warming Drawer or Premium

Storage Drawer:

1. Place the outside of your foot against the bottom front of the

warming drawer or premium storage drawer, and grasp the

lower right-hand or left-hand side of the control panel as

shown.

NOTE: If your countertop is mounted with a backsplash, it

may be necessary to grasp the range higher than is shown in

the illustration.

2. Slowly attempt to tilt the range forward.

If you encounter immediate resistance, the range foot is

engaged in the anti-tip bracket.

3. If the rear of the range lifts more than ½" (1.3 cm) off the floor

without resistance, stop tilting the range and lower it gently

back to the floor. The range foot is not engaged in the anti-tip

bracket.

IMPORTANT: If there is a snapping or popping sound when lifting

the range, the range may not be fully engaged in the bracket.

Check to see if there are obstructions keeping the range from

sliding to the wall or keeping the range foot from sliding into the

bracket. Verify that the bracket is held securely in place by the

mounting screws.

4. Slide the range forward, and verify that the anti-tip bracket is

securely attached to the floor or wall.

5. Slide range back so the rear range foot is inserted into the

slot of the anti-tip bracket.

IMPORTANT: If the back of the range is more than 2" (5.1 cm)

from the mounting wall, the rear range foot may not engage the

bracket. Slide the range forward and determine if there is an

obstruction between the range and the mounting wall. If you

need assistance or service, refer to the "Assistance or Service"

section of the Use and Care Guide, or the cover or "Warranty"

section of the User Instructions, for contact information.