- ページ 7

アクセサリー A&E Systems WeatherPro Oasis EliteのPDF 診断サービスマニュアルをオンラインで閲覧またはダウンロードできます。A&E Systems WeatherPro Oasis Elite 14 ページ。

ページを印刷する

3.1.5 To check the WeatherPro remote switch

connection (Brown, Green, & Yellow) wire

use a jumper wire and connect the Yellow

to Brown. You should hear the relay click.

Then connect the Green to Brown and you

should hear another click.

3.1.6 Check the Oasis Elite remote switch wire

and the output wire at the same time. The

remote switch wires are Brown/White,

Green/White and Yellow/White. The out-

put wire is Red/White and Blue. Connect

the positive lead of the digital volt meter

to the Red/White wire position of the pig-

tail and the negative to the Blue wire po-

sition of the pigtail. Jump across the Yel-

low/White and brown/White wire. You

should hear the relay click and the volt-

age meter should read (–) negative 12.5

VDC (minimum). Jump across the Green/

White and the Brown/White wire. You

should hear another relay click and the

volt meter should read (+) positive 12 VDC

(minimum).

3.1.7 To check the ignition interlock function

(WeatherPro Only), apply (+) positive 12

VDC to the Pink ignition interlock wire. Re-

do test in 3.1.4. There should be no read-

ings or relay clicks when the rocker switch

is placed in the extend position or the key

FOB extend button is pressed.

3.1.8 The circuit board contains an audible

alarm to alert the user when there is a

problem with the wind sensor or wind

sensor cable. To test this alarm discon-

nect the FLAT four (4) conductor cable

from the side of the control box. Place the

wind sensor switch in the ENABLE (ON)

position. The alarm should beep from in-

side the control box. If this occurs under

normal operation this would indicate a

problem with the wind sensor wire or the

connection between the wire and the cir-

cuit board or the wire and the wind sen-

sor. See Section 1.6 and Section 2.1.

3.2

Control Box Rocker Switch

The awning can be operated at the control box

by using the rocker switch located on the cover

of the control box. To test the switch, press ex-

tend or retract and you should hear a relay click.

If after all other circuit board checks are made

and no click is present switch is defective. Re-

place.

3.3 Wind Sensor Toggle Switch

The toggle switch turns the wind sensor feature

on and off. When the switch is in the DISABLE

(OFF) position the awning will not automatically

retract if threating winds are present. When in

the ENABLE (ON) positiion the awning will auto-

matically retract if the wind exceeds the preset

setting.

If one or more of the above tests do not perform

properly the circuit board is probably defective.

Replace the control box assembly.

3.4 Wiring Diagram (See Page 6, FIG. 3.4)

SECTION 4 Remote Switch

4.1 If awning does not work using the remote switch,

disconnect both the WeatherPro and the Oasis

Elite pigtail. Check for 12VDC on the control box

end of the pig tail. See Section 3.1.4 and 3.1.6. If

there is 12 VDC at this point depress the remote

switches and listen for the relays to click. If no

clicking is heard replace appropiate remote

switch.

FIG. 4.1

SECTION 5 Remote Key FOB

5.1

The remote key FOB is powered by a 12 VDC

type 23A battery. The operational range is up to

30 feet. This distance will vary depending on the

battery condition. To change the battery, remove

screw in back of key FOB and replace it with a

type 23A 12VDC battery.

FIG. 5.1

EXTEND

RETRACT

EXTEND

PATIO

RETRACT

EXTEND

DOOR

Battery

RETRACT

23A 12V