- ページ 18
船舶用GPSシステム Garmin GNS 530WのPDF クイック・リファレンスをオンラインで閲覧またはダウンロードできます。Garmin GNS 530W 23 ページ。 For continued airworthiness bell 206b
Garmin GNS 530W にも： パイロット・マニュアル補遺 (24 ページ), パイロット・マニュアル補遺 (50 ページ), パイロット・マニュアル補遺 (50 ページ), パイロット・マニュアル補遺 (24 ページ), 補足マニュアル (12 ページ), クイック・リファレンス (25 ページ), 取扱説明書 (23 ページ)
ページを印刷する
Activating an Approach
1. With an approach loaded in the active flight plan,
press the PROC key to display the Procedures Page.
2. Turn the large right knob to highlight "Activate
Approach?".
3. Press ENT.
Activating an Approach with Vectors-to-Final
The "Activate Vectors-To-Final?" option allows you to
activate the final course segment of the approach. This option
assumes you will receive vectors to the final approach course
and guides you to intercept the final
course, before reaching the FAF.
1.
With an approach loaded
in the active flight plan,
press the PROC key to
display the Procedures
Page.
2.
Turn the large right
knob to highlight "Activate Vectors-To-Final?".
Press ENT.
3.
Flying an Approach
Due to the variety of available approach procedures, the
specific steps required will vary according to the approach
selected. Keep the following guidelines in mind while flying the
approach:
• The GNS 500W-series units are designed to complement
your printed approach plates and improve situational
awareness throughout the
approach. However, you must
always fly an approach as
it appears on the approach
plate.
• You will typically select the
destination airport as the last
waypoint in the active flight
16
APPROACHES
plan or by using the direct-to key. Doing so ensures that
the desired waypoint will automatically appear when
choosing the "Select Approach?" option for the Procedures
Page. (Otherwise, you must first choose the airport, then
the approach procedure).
• In the GNS 530W, when a localizer-based approach (such
as an ILS) is loaded, the desired frequency is automatically
placed in standby on the VLOC window. To activate the
frequency, press the VLOC flip-flop key.
• In the GNS 530W, if the VLOC receiver will be used for
the approach, be sure to switch the external CDI (or HSI)
to "VLOC" by pressing the CDI key. (VLOC will appear
directly above the CDI key).
• In the GNS 530W, an "ILS CDI Selection" setting of "Auto"
provides automatic switching to "VLOC" as you intercept
the final approach course. When the ILS approach is
activated (and the correct frequency is active in the VLOC
window), the GNS 530W will automatically switch within
1.2 nautical miles left or right of the approach course. This
switch can take place anywhere from 2.0 to 15.0 nautical
miles from the FAF. The switch occurs gradually to prevent
abrupt CDI changes. This does not occur automatically
when configured for the King KAP140/KFC225 autopilots
as Auto ILS CDI Selection is not allowed.
• As you progress to each waypoint, a waypoint alert mes-
sage (e.g., "Next DTK ###° in x sec") will appear in the
lower right corner of the display.
• When you should begin a course change (via a standard
rate turn), turn advisories ("Left to ###° in x sec") will
appear in the lower right corner of the display.
• For GPS-based approaches, receiver autonomous integrity
monitoring (RAIM) will monitor satellite conditions and
alert you—using an "INTEG" annunciation at the bottom
left corner of the display —if protection limits cannot be
maintained. If this occurs, the GPS receiver should not
be used for primary navigation guidance. Revert to an
alternate navigation source, such as the GNS 530W' s VOR/
Localizer receiver, or select an alternate destination airport.