- ページ 4

船舶用GPSシステム Garmin GPS 152HのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GPS 152H 36 ページ。 Declaration of conformity
Garmin GPS 152H にも：クイック・スタート・マニュアル (49 ページ), オーナーズマニュアル (32 ページ), 重要な安全情報 (48 ページ), 適合宣言 (6 ページ)

ページを印刷する

to install the GPS 152H device on the mounting bracket:

1. Loosely attach the two mounting knobs to the sides of the GPS 152H device.

2. Insert the device into the mounting bracket. The bracket is designed for a tight fit to provide additional support when tilting the unit.

3. Adjust the angle of the device, and tighten the two mounting knobs until the device is snug.

Installing the GPS 152H Wiring Harness

The GPS 152H device comes with a wiring harness that

connects the device to power and to optional NMEA 0183

devices.

notes:

•

Use an AGC/ 3AG - 1.5 A replacement fuse.

•

If it is necessary to extend the power and ground wires,

use 22 AWG wire.

•

You can wire the harness directly to the battery, or if

your boat has an electrical system, you might be able to

wire the harness to an unused holder on the fuse block.

If you use the boat fuse block, remove the in-line fuse

holder on the power wire of the harness..

The maximum input voltage is 40 Vdc. Do not exceed this voltage because this can damage the device and void the warranty.

NOTE: During a typical installation, use only the red and black wires. The other wires do not have to be connected for normal operation of the

device. For information on connecting to a NMEA 0183 device, see

Connecting the Wiring Harness to Power

1. Use a test light or a voltmeter to determine the polarity of the voltage source.

2. Connect the red (+ or positive) wire to the positive voltage terminal. (If you use the

fuse block on the boat, route the positive connection through the fuse, as shown on the

diagram.)

3. Connect the black (- or ground) wire to the negative voltage terminal.

4. Install or check the 1.5 A fuse (in the in-line fuse holder, or on the fuse block of the boat).

Connecting the Wiring Harness to a nMEa 0183 Device

You can connect the GPS 152H device to other NMEA compatible equipment, such as a

DSC or AIS device. Refer to the wiring diagram for connecting the device to NMEA 0183-compatible devices.

GPS 152H device

Wire color

Fuse

3 A

Red (power)

Black (ground)

Blue (out)

Brown (in)

Wiring a GPS 152H Device to a Standard nMEa 0183 Device

To the

GPS 152H

device

GPS 152H Wiring Harness

notice

below.

Boat ground

Battery

10–0 Vdc

Wire function

Power

Power ground

NMEA ground

NMEA Rx/A (+)

NMEA Tx/A (+)

Wire Color

Wire Function

Pin 1—red

Power (10–0 Vdc)

Ground (power and

Pin 2—black

NMEA)

Pin 3—blue

NMEA com 1 Tx (out)

Pin —brown

NMEA com 1 Rx (in)

Pin 5—white

NMEA com 2 Rx (in)

Pin 6—yellow

Alarm low

Pin 7—green

Unused

1.5 A fuse

To 10–0 Vdc boat supply

2A 3A

—

To device

Fuse Block Example

NMEA 0183

compliant device

GPS 152H Installation Instructions