Garmin GPS 152H Інструкція з монтажу Посібник з монтажу - Сторінка 4
Переглянути онлайн або завантажити pdf Інструкція з монтажу Посібник з монтажу для Морська система GPS Garmin GPS 152H. Garmin GPS 152H 36 сторінок. Declaration of conformity
Також для Garmin GPS 152H: Посібник із швидкого старту (49 сторінок), Посібник користувача (32 сторінок), Важлива інформація про безпеку (48 сторінок), Декларація про відповідність (6 сторінок)
Друкувати сторінку
to install the GPS 152H device on the mounting bracket:
1. Loosely attach the two mounting knobs to the sides of the GPS 152H device.
2. Insert the device into the mounting bracket. The bracket is designed for a tight fit to provide additional support when tilting the unit.
3. Adjust the angle of the device, and tighten the two mounting knobs until the device is snug.
Installing the GPS 152H Wiring Harness
The GPS 152H device comes with a wiring harness that
connects the device to power and to optional NMEA 0183
devices.
notes:
•
Use an AGC/ 3AG - 1.5 A replacement fuse.
•
If it is necessary to extend the power and ground wires,
use 22 AWG wire.
•
You can wire the harness directly to the battery, or if
your boat has an electrical system, you might be able to
wire the harness to an unused holder on the fuse block.
If you use the boat fuse block, remove the in-line fuse
holder on the power wire of the harness..
The maximum input voltage is 40 Vdc. Do not exceed this voltage because this can damage the device and void the warranty.
NOTE: During a typical installation, use only the red and black wires. The other wires do not have to be connected for normal operation of the
device. For information on connecting to a NMEA 0183 device, see
Connecting the Wiring Harness to Power
1. Use a test light or a voltmeter to determine the polarity of the voltage source.
2. Connect the red (+ or positive) wire to the positive voltage terminal. (If you use the
fuse block on the boat, route the positive connection through the fuse, as shown on the
diagram.)
3. Connect the black (- or ground) wire to the negative voltage terminal.
4. Install or check the 1.5 A fuse (in the in-line fuse holder, or on the fuse block of the boat).
Connecting the Wiring Harness to a nMEa 0183 Device
You can connect the GPS 152H device to other NMEA compatible equipment, such as a
DSC or AIS device. Refer to the wiring diagram for connecting the device to NMEA 0183-compatible devices.
GPS 152H device
2
2
Wire color
Fuse
3 A
Red (power)
Black (ground)
Blue (out)
>
Brown (in)
>
Wiring a GPS 152H Device to a Standard nMEa 0183 Device
To the
To the
GPS 152H
GPS 152H
device
device
4
4
3
3
5
5
6
6
1
1
7
7
GPS 152H Wiring Harness
GPS 152H Wiring Harness
notice
below.
Boat ground
Boat ground
-
+
Battery
10–0 Vdc
Wire function
Power
Power ground
NMEA ground
NMEA Rx/A (+)
NMEA Tx/A (+)
Wire Color
Wire Color
Wire Function
Wire Function
Pin 1—red
Pin 1—red
Power (10–0 Vdc)
Power (10–0 Vdc)
Ground (power and
Ground (power and
Pin 2—black
Pin 2—black
NMEA)
NMEA)
Pin 3—blue
Pin 3—blue
NMEA com 1 Tx (out)
NMEA com 1 Tx (out)
Pin —brown
Pin —brown
NMEA com 1 Rx (in)
NMEA com 1 Rx (in)
Pin 5—white
Pin 5—white
NMEA com 2 Rx (in)
NMEA com 2 Rx (in)
Pin 6—yellow
Pin 6—yellow
Alarm low
Alarm low
Pin 7—green
Pin 7—green
Unused
Unused
1.5 A fuse
1.5 A fuse
To 10–0 Vdc boat supply
To 10–0 Vdc boat supply
2A 3A
2A 3A
—
—
+
+
To device
To device
Fuse Block Example
Fuse Block Example
NMEA 0183
compliant device
>
>
GPS 152H Installation Instructions