- ページ 3
船舶用GPSシステム Garmin GPSMAP 8000 SeriesのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GPSMAP 8000 Series 14 ページ。 Installation instructions
Garmin GPSMAP 8000 Series にも: オーナーズマニュアル (36 ページ), クイック・スタート・マニュアル (4 ページ), 取扱説明書 (15 ページ), オーナーズマニュアル (43 ページ)
![Garmin GPSMAP 8000 Series 取付説明書](/uploads/products/server2/2323508/2323508.png)
NOTE: To prevent corrosion of the metal contacts, cover
unused connectors with the attached weather caps.
20
Place the device into the cutout.
21
Secure the device to the mounting surface using the included
M4 screws
.
22
Insert the included plugs over each of the M4 screw heads.
23
Install the decorative bezel by snapping it in place around the
edges of the device.
Card Reader Mounting Considerations
This device should be mounted in a location that is not exposed
to extreme temperatures or conditions. The temperature range
for this device is listed in the product specifications. Extended
exposure to temperatures exceeding the specified temperature
range, in storage or operating conditions, may cause device
failure. Extreme-temperature-induced damage and related
consequences are not covered by the warranty.
The card reader can be flush mounted in the dashboard using
the included hardware. When selecting a mounting location,
observe these considerations.
• The card reader should be mounted in an accessible
location. You must be able to access the card reader when
necessary to insert and remove memory cards containing
additional mapping and device updates, and to transfer user
data.
• To avoid interference with a magnetic compass, the device
should not be installed closer to a compass than the
compass-safe distance value listed in the product
specifications.
• The location must allow room for the routing and connection
of the cables.
Mounting the Card Reader
Be careful when cutting the hole to flush mount the device.
There is only a small amount of clearance between the case and
the mounting holes, and cutting the hole too large could
compromise the stability of the device after it is mounted.
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
The included template and hardware can be used to flush mount
the device at the selected location.
1
Trim the flush-mount template and make sure it fits in the
location where you want to mount the device.
2
Remove the protective liner from the back of the template
and adhere it to the location where you want to mount the
device.
3
Using a 6 mm (¼ in.) drill bit, drill one or more of the holes
inside the corners of the solid line on the template to prepare
the mounting surface for cutting.
4
Using a jigsaw, cut the mounting surface along the inside of
the solid line indicated on the template.
5
Place the device in the cutout to test the fit.
6
If necessary, use a file and sandpaper to refine the size of
the cutout.
7
After the device
fits correctly in the cutout, make sure the
mounting holes on the device line up with the pilot holes
on the template.
GPSMAP 8000 Series Installation Instructions
NOTICE
NOTICE
8
If the mounting holes on the device do not line up, mark the
new pilot-hole locations.
9
Using a center punch, indent the pilot holes and drill the
clearance counterbore through the gel-coat layer as advised
in the notice.
10
Remove the template from the mounting surface.
11
If you will not have access to the back of the device after you
mount it, connect all necessary cables to the device before
placing it into the cutout.
12
Place the device into the cutout.
13
Secure the device to the mounting surface using the included
screws
.
14
Install the decorative bezel by snapping it in place around the
edges of the device.
Antenna Mounting Considerations
You can mount the antenna on a flat surface, install it under
fiberglass, or attach it to a standard 1 in. OD, 14 threads per
inch, pipe-threaded pole (not included). You can route the cable
outside of the pole or through the pole. For best performance,
consider these guidelines when selecting the antenna mounting
location.
• To ensure the best reception, the antenna should be
mounted in a location that has a clear, unobstructed view of
the sky in all directions
• The antenna should not be mounted where it is shaded by
the superstructure of the boat
mast.
• The antenna should not be mounted near the engine or other
sources of Electromagnetic Interference (EMI)
• If a radar is present, the antenna should be mounted above
the path of the radar
mounted below the path of the radar
.
, a radome antenna, or the
.
. If necessary, the antenna may be
.
3