- ページ 5

船舶用GPSシステム Garmin GPSMAP 8000 SeriesのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Garmin GPSMAP 8000 Series 14 ページ。 Installation instructions
Garmin GPSMAP 8000 Series にも：オーナーズマニュアル (36 ページ), クイック・スタート・マニュアル (4 ページ), 取扱説明書 (15 ページ), オーナーズマニュアル (43 ページ)

ページを印刷する

With the antenna installed on the pole mount, fill the

remaining gap in the vertical cable slot with a marine sealant

(optional).

Attach the pole to the boat if it is not already attached.

Route the cable away from sources of electronic interference.

Mounting the Antenna with the Cable Routed Through the

Pole

Before you permanently mount the antenna, you must test the

mounting location for correct operation

Considerations, page

3).

Position a standard 1 in. OD, 14 threads per inch, pipe-

threaded pole (not included) in the selected location, and

mark the approximate center of the pole.

Drill a hole using a 19 mm (

pass through.

Fasten the pole to the boat.

Thread the pole-mount adapter onto the pole.

Do not overtighten the adapter.

Route the cable through the pole and connect it to the

antenna.

Place the antenna on the pole-mount adapter and twist it

clockwise to lock it in place.

Secure the antenna to the adapter with the included M3 set

screw

With the antenna installed on the pole mount, fill the vertical

cable slot

with a marine sealant (optional).

Route the cable away from sources of electronic interference.

Mounting the Antenna Under the Deck

Before attaching the under-deck mounting bracket to the

surface, verify the included screws will not penetrate the

surface. If the included screws are too long, you must purchase

surface-appropriate screws to complete the installation.

Before you permanently mount the antenna, you must test the

mounting location for correct operation

Considerations, page

3).

Because the antenna cannot acquire signals through metal, it

must be mounted under a fiberglass surface only.

Place the adhesive pads

bracket

GPSMAP 8000 Series Installation Instructions

(Antenna Mounting

in.) drill bit for the cable to

NOTICE

(Antenna Mounting

on the under-deck mounting

Place the antenna in the under-deck mounting bracket.

Adhere the under-deck mounting bracket to the mounting

surface.

Secure the under-deck mounting bracket to the mounting

surface with screws.

Connect the cable to the antenna

Route the cable away from sources of electronic interference.

Cable and Connection Considerations

A blue rubber seal is included for each DVI port on the device.

This seal must be installed between each DVI port and DVI-

cable connector to avoid damage to the connectors.

• For easer cable routing, the power, NMEA

Marine Network cables are packaged without the locking

rings installed. You should route the cables before you install

the locking rings.

• After connecting a locking ring to a cable, make sure the ring

is securely connected and the o-ring is in place so the power

or data connection remains secure.

• The device should be connected to the same power source

as the card reader. If this is not possible, the devices must be

connected to the same ground.

Station Connection Considerations

This device can be set up in conjunction with other compatible

Garmin devices to work together as a station. When planning

stations on your boat, observe these considerations.

• Devices earlier than the GPSMAP 8000 series and GPSMAP

8500 series cannot be used in a station.

• Although it is not necessary, it is recommended that you

install all of the devices you plan to use in one station near

each other.

• No special connections are necessary to create a station, as

long as all of the devices are connected to the Garmin Marine

Network

(Garmin Marine Network Considerations, page

• Stations are created and modified using the device software.

See the owner's manual provided with the device for more

information.

Connecting to Power

When connecting the power cable, do not remove the in-line

fuse holder. To prevent the possibility of injury or product

damage caused by fire or overheating, the appropriate fuse

must be in place as indicated in the product specifications. In

addition, connecting the power cable without the appropriate

fuse in place will void the product warranty.

Route the power cable to the power source and to the device.

Connect the red wire to the positive (+) battery terminal, and

connect the black wire to the negative (-) battery terminal.

NOTICE

0183, and Garmin

WARNING

6).