ゲートウェイ 2N EasyGate ProのPDF クイックスタートをオンラインで閲覧またはダウンロードできます。2N EasyGate Pro 2 ページ。 Umts gateway
2N EasyGate Pro にも: クイックスタート (4 ページ), クイックスタート (4 ページ), クイックスタート (4 ページ)
Outgoing call
· Suppose that the SIM card has been
inserted, the PIN entered or not required,
and
EasyGate
is
registered
to
network – the GSM Network LED is
permanently on.
· Hook off the telephone, you can hear the
dial tone and the Line LED starts flashing.
· Dial
the
GSM
subscriber
number.
EasyGate receives tone dialing (DTMF) by
default. If your telephone transmits pulse
dialing only, program EasyGate to receive
pulse dialing. When you make a delay in
your
dialing
longer
than
(programmable),
the
connection
established.
· If the called subscriber is available, you
can hear the ringing tone. If not, you can
hear the busy tone or any of the GSM
provider's messages.
· When the called subscriber answers the
call, the call is established. The Line LED
is permanently on during the call.
· Hang up to terminate the call. The Line
LED goes off. If the called subscriber is
the first to hang up, you can hear the
busy tone and hang up.
Incoming call
· An incoming call is signaled by ringing.
The Line LED flashes during ringing.
· Hook off the phone to establish the call.
The Line LED is permanently on during
the call.
· For call termination see the Outgoing call
section.
Fax and data connection
(only fax models)
EasyGate with fax converter has ability to
manage fax messages using analogue fax
Group 3 and data connection using analog
In the GSM network, GPRS data transfer is suspended during voice calls
and do not continue until the voice call is finished.
EC Declaration of Conformity
Hereby, 2N TELEKOMUNIKACE a.s., declares that the 2N® EasyGate PRO product is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. Refer to the CD-ROM or our
website www.2n.cz for the Declaration of conformity.
© 2011, 2N TELEKOMUNIKACE a.s. – Prague, LH 1711, v.1.01
modem connected to telephone line. The
fax or data service must be registered with
your GSM operator.
GSM
· Outgoing FAX call or Data connection
Before
destination
number
*01* for fax call or *02* for data call.
When connected device generates calling
tone, this preset is not necessary.
· Incoming FAX call or data connection
It is recommended to activate separate
fax
number
on
your
SIM
multinumbering
scheme.
5s
messages and data connection should be
is
routed to appropriate number.
If
the
fax
or
data
number
activated, the call from analogue network
is not detected as fax or data call and is
routed via the analogue channel of GSM
network,
the
connection
established. In this case it is possible to
set fax engine in the gateway to receive
the next call as fax or data call. This
setting can be done permanent - see the
manual on CD-ROM. This function is not
guaranteed by all operators.
Configuration over USB
· For
PC
configuration
of
EasyGate
necessary
to
install
PCManager UNI.
Connect EasyGate to PC using USB cable.
· Virtual serial port(USB serial port FTDI) is
created immediately after linking PC and
EasyGate.
This
port
is
PCManager
to
communicate
EasyGate. When the port isn't activated
automatically use driver on CD
· The COM port number of virtual serial
port has to be set in PCManager.
· Detailed description is in the product
manual on CD-ROM.
dial
code
card
–
Fax
is
not
can´t
be
is
used
by
with