2N EasyGate Pro 빠른 시작

{카테고리_이름} 2N EasyGate Pro에 대한 빠른 시작을 온라인으로 검색하거나 PDF를 다운로드하세요. 2N EasyGate Pro 2 페이지. Umts gateway
2N EasyGate Pro에 대해서도 마찬가지입니다: 빠른 시작 (4 페이지), 빠른 시작 (4 페이지), 빠른 시작 (4 페이지)

페이지 인쇄

Outgoing call

· Suppose that the SIM card has been

inserted, the PIN entered or not required,

and

EasyGate

registered

network – the GSM Network LED is

permanently on.

· Hook off the telephone, you can hear the

dial tone and the Line LED starts flashing.

· Dial

the

GSM

subscriber

number.

EasyGate receives tone dialing (DTMF) by

default. If your telephone transmits pulse

dialing only, program EasyGate to receive

pulse dialing. When you make a delay in

your

dialing

longer

than

(programmable),

the

connection

established.

· If the called subscriber is available, you

can hear the ringing tone. If not, you can

hear the busy tone or any of the GSM

provider's messages.

· When the called subscriber answers the

call, the call is established. The Line LED

is permanently on during the call.

· Hang up to terminate the call. The Line

LED goes off. If the called subscriber is

the first to hang up, you can hear the

busy tone and hang up.

Incoming call

· An incoming call is signaled by ringing.

The Line LED flashes during ringing.

· Hook off the phone to establish the call.

The Line LED is permanently on during

the call.

· For call termination see the Outgoing call

section.

Fax and data connection

(only fax models)

EasyGate with fax converter has ability to

manage fax messages using analogue fax

Group 3 and data connection using analog

In the GSM network, GPRS data transfer is suspended during voice calls

and do not continue until the voice call is finished.

EC Declaration of Conformity

Hereby, 2N TELEKOMUNIKACE a.s., declares that the 2N® EasyGate PRO product is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC. Refer to the CD-ROM or our

website www.2n.cz for the Declaration of conformity.

modem connected to telephone line. The

fax or data service must be registered with

your GSM operator.

GSM

· Outgoing FAX call or Data connection

Before

destination

number

*01* for fax call or *02* for data call.

When connected device generates calling

tone, this preset is not necessary.

· Incoming FAX call or data connection

It is recommended to activate separate

fax

number

your

SIM

multinumbering

scheme.

messages and data connection should be

routed to appropriate number.

the

fax

data

number

activated, the call from analogue network

is not detected as fax or data call and is

routed via the analogue channel of GSM

network,

the

connection

established. In this case it is possible to

set fax engine in the gateway to receive

the next call as fax or data call. This

setting can be done permanent - see the

manual on CD-ROM. This function is not

guaranteed by all operators.

Configuration over USB

· For

configuration

EasyGate

necessary

install

PCManager UNI.

Connect EasyGate to PC using USB cable.

· Virtual serial port(USB serial port FTDI) is

created immediately after linking PC and

EasyGate.

This

port

PCManager

communicate

EasyGate. When the port isn't activated

automatically use driver on CD

· The COM port number of virtual serial

port has to be set in PCManager.

· Detailed description is in the product

manual on CD-ROM.

dial

code

card

–

Fax

not

can´t

used

with