- ページ 10
スキャナー Fujitsu ScanSnap iScanner fi-6010NのPDF スタートマニュアルをオンラインで閲覧またはダウンロードできます。Fujitsu ScanSnap iScanner fi-6010N 21 ページ。 Network adf scanner
Fujitsu ScanSnap iScanner fi-6010N にも： 仕様 (2 ページ), スタートマニュアル (21 ページ), パンフレット＆スペック (2 ページ), スタートマニュアル (45 ページ), 洗浄方法 (2 ページ), 洗浄方法 (2 ページ)
ページを印刷する
4. Select whether or not to enable SSL.
Select the [On] button enables SSL. If SSL is
enabled, press the [Regenerate] button to create
another SSL Certificate. When a new SSL Certifi-
cate is created, the contents of the certificate are
changed. The contents of the SSL Certificate are
as follows.
z Issued by
Displays the SSL Certificate issuer.
z Valid from
Displays the SSL Certificate expiration date.
The expiration date is five years from the
date on which the certificate was created.
This is shown in date form.
Selecting the [Off] button disables SSL.
5. Press the [OK] button.
D The communication settings are set.
The following settings combinations
ATTENTION
are not possible.
z Port Number "80" and SSL "On"
z Port Number "443" and SSL "Off"
Continue with the DNS settings.
3.7 Setting the DNS Server
A primary DNS and secondary DNS can be set.
1. Select the [Network Settings] tab on the top
menu.
2. Select the [DNS Server] tab on the left side
menu.
D The "DNS Server" screen appears.
3. Enter the following numerical addresses:
z Primary DNS
z Secondary DNS
If a DNS server setting is not required, enter
"0.0.0.0".
A Secondary DNS cannot be set
ATTENTION
without a Primary DNS.
DNS Dynamic Update and DNS Suf-
fix can also be set.
HINT
The current FQDN is shown for the
FQDN. However, if the scanner is not
connected to the network, the FQDN
may not be displayed correctly.
4. Press the [OK] button.
D The information entered is set.
Continue with the WINS settings.
3.8 Setting the WINS Server
A primary WINS and secondary WINS can be set.
1. Select the [Network Settings] tab on the top
menu.
2. Press the [
] button on the left side menu.
D Scroll the left side menu down until the
[WINS Sever] tab appears.
3. Select the [WINS Server] tab on the left side
menu.
D The "WINS Server" screen appears.
9
4. Enter the following numerical addresses:
z Primary WINS
z Secondary WINS
If a WINS server setting is not required, enter
"0.0.0.0".
A Secondary WINS cannot be set
ATTENTION
without a Primary WINS.
5. Press the [OK] button.
D The information entered is set.
Next, check the network connection.
3.9 Checking the Network
Connection
The network connection may be checked by performing
a ping test.
1. Select the [Network Settings] tab on the top
menu.
2. Press the [
] button on the left side menu.
D Scroll the left side menu down until the [Ping]
tab appears.
3. Select the [Ping] tab on the left side menu.
D The "Ping" screen appears.
4. Enter the IP address, host name, or FQDN for
the server to be used to check the network
connection.
z For an IP address
The following format should be used
xxx.xxx.xxx.xxx (xxx is a value from 0 to 255).
z For a host name or FQDN
Up to 255 characters may be used.
5. Press the [Ping] button.
D A ping test is performed and the results are
displayed. If the result shows "Lost=0 (0%
loss)", the network connection is functioning
normally. For any other result, refer to
"Checking Basic Network Operation with a
Ping Test" (page 22).
After performing all settings, restart the system.
3.10 Restarting the System
1. Press the [Logout] button.
D The restart confirmation screen appears.
2. Press the [Restart] button.
D The scanner restarts, and the "Login" screen
appears.
Next, install the Admin Tool.
10