- ページ 15

ストレージ Fujitsu ETERNUS DX DiskのPDF 設定マニュアルをオンラインで閲覧またはダウンロードできます。Fujitsu ETERNUS DX Disk 35 ページ。 Server connection, fcoe for linux driver settings for converged network adapter cards
Fujitsu ETERNUS DX Disk にも: ユーザーマニュアル (35 ページ), ユーザーマニュアル (42 ページ), 設定マニュアル (28 ページ), 設定マニュアル (44 ページ), 設定マニュアル (28 ページ), 設定マニュアル (29 ページ), 設定マニュアル (25 ページ), 設定マニュアル (32 ページ), 設定マニュアル (31 ページ), 設定マニュアル (43 ページ), 設定マニュアル (21 ページ), 設定マニュアル (24 ページ)

Fujitsu ETERNUS DX Disk 設定マニュアル
Chapter 1
Setup Procedure for Emulex Converged Network Adapter Cards
1.2
Setting Up the Converged Network Adapter Cards
12
The window shown in
In this example, check that item #1 is listed as "Used", that the "WWPN" is set to the actual ETERNUS
DX400 series WWPN, and that the "LUN" is set to "00" and that it bears the "Primary Boot" label.
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
01:
Mem Base:
Port Name:
Vlan ID:
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
-------------------------------------------------------------------------------
===> Enter <Esc> to Previous Menu
13
Press the [Esc] key twice to return to the window shown in
If the Converged Network Adapter card has a dual port, or if multiple Converged Network Adapter cards
to be installed, repeat
14
Press the [Esc] key to reboot.
--------------------------------------------------------
Reboot the system for all changes to take effect.
--------------------------------------------------------
===> Y
1.2.3

Installing VMware ESX

VMware ESX should be installed now if it has not yet been installed in the server. Refer to the following
URL for details.
http://www.vmware.com/support/pubs
Converged Network Adapter card driver should be downloaded and installed from the following URL:
https://my.vmware.com/web/vmware/downloads
1.2.4

Setting Up the Converged Network Adapter Card Driver

Change the parameters for the Converged Network Adapter card driver.
FUJITSU Storage ETERNUS DX Configuration Guide -Server Connection- (FCoE) for VMware
Step 7
reappears.Check the settings.
Emulex OneConnect FCoE BIOS Utility, xxxxxxxx
OCexxxxx-F:
CD4C0000
Firmware Version:
xxxxxxxx xxxxxxxx
xxxx
DCBX mode:
CEE mode
List of Saved Boot Devices:
1. Used
DID:xxxxxx WWPN:2040000B 5D6A0012 LUN:00
2. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
3. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
4. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
5. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
6. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
7. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
8. Unused
DID:000000 WWPN:00000000 00000000 LUN:00
< / > to Highlight, <Enter> to Select
Copyright (c) 1997-2009 Emulex. All rights reserved.
Step 2
through
Your changes have been saved.
REBOOT THE SYSTEM? (Y/N):
Copyright 2015 FUJITSU LIMITED
Bus#: xx Dev#: xx Func#: xx
xxx.xxx
BIOS: Enabled!
Node Name:
xxxxxxxx xxxxxxxx
Step
2.
Step
13.
15
Primary Boot
®
ESX
P3AM-4772-11ENZ0