- ページ 5

バスルーム設備 Kohler Elosis 18057T-B-CPのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Kohler Elosis 18057T-B-CP 12 ページ。 Sensor faucet

ページを印刷する

技术参数

电源：直流 4节5号碱性电池(LR06×4)

交流电压220V,频率50/60Hz

检测时间：小于0.5秒

关阀延时：0.5～1秒

感应距离：自动调节

流量：水压为0.3MPa 时，流量不大于2.0L/min

超时用水控制：超时用水1分钟，自动止水。

环境温度：1 ～55

进水温度：0.5～71

适用水压：0.05～

安装步骤

如何安装水龙头

一龙头与面盆的安装固定

将固定螺杆(2)安装到水龙头(1)底部

处。再把垫片(3)套在固定螺杆上。并

嵌入水龙头底部的盘槽中。然后将电

源线(7)和进水软管(8)穿过安装孔，从

面盆下方将固定橡胶垫片(4)固定金属

垫片(5)和固定螺母(6)对齐固定螺杆向

上套入。调整水龙头电源线及进水软

管的位置。用扳手拧紧固定螺母以便

把水龙头固定在面盆上。

二安装控制组件

拧下控制盒盖(10)螺钉(11)，打开控制

盒(9)，根据安装尺寸图（图一）在墙

壁合适的位置钻孔，打入膨胀管

(12)，使控制盒紧贴墙面，再用螺钉

(13)将其固定在墙壁上。

注意：控制盒长边端需竖直放置，出

水口位置可根据需要左右调整。

将软管(16)一端与三通进水软管组件

(17)连接，另一端与控制组件(15)进水

口连接，再将出水口与龙头出水软管

(14)连接，三通进水软管组件另外两端

与角阀(18)连接。

对于单冷龙头，将软管一端与滤网接头

(19)相连，另一端与角阀连接即可。

1248536-T01-C

℃

PARAMETERS

Power: DC 4 pieces of AA size alkaline batteries

AC 220V, 50/60Hz

Senser Duration: Less than 0.5s

Shut-off Delay: 0.5~1s

Sensing Distance: Automatic adjustment

Flow Rate: No more than 2.0L/min at 0.3MPa.

Overtime Flowing Control: Automatically stop flushing when

the faucet senses an object for more than 1 minute

continuously

Ambient Temperature: 1~55℃

Supply Water Temperature: 0.5~71℃

Supply Water Pressure: 0.05~0.86MPa

图一

INSTALLATION

How to Install the Faucet

1. Fasten faucet on lavatory:

Install the stud (2) to the underside of the

faucet (1). Slide the gasket (3) over the

stud, and then seat the gasket in the groove

on the underside of the sprout. Cross power

cord (7) and water inlet hose (8) through

mounting hole, slide rubber washer (4),

metal washer (5) and nut (6) onto the stud

from under the sink. Adjust faucet power

cord and water inlet hose position, fasten nut

to secure faucet on lavatory mounting

surface by wrench.

2. Install Control Assy.

Unscrew valve cover (10) screw (11)

by screwdriver,

open

(9). Determine proper mounting location

per rough –in (Fig 1), then punch

expansion tube (12) in. Place valve box

against the wall and then secure control

valve assembly on the wall by bolts (13).

Note: place the long end of control box

upright, water outlet position shall be

adjusted left/right based on requirements.

Connect hose (16) to Tee water inlet

hose assembly(17), and then connect

water outlet with faucet water outlet

hose (14). Connect Tee water inlet hose

other two ends with valve (18).

For cold water faucet, connect hose

to the cylinder(19) and then connect

with valve.

valve

cover