- ページ 5

配管製品 Billi 926065のPDF インストレーション・マニュアルをオンラインで閲覧またはダウンロードできます。Billi 926065 7 ページ。 Dispenser options: xl and mixer tap, al
Billi 926065 にも：ユーザーマニュアル (9 ページ)

ページを印刷する

Installing Underbench Module cont.

Connect to Drainage Point

Option 1: to dishwasher nipple on waste trap

i. Drill hole in dishwasher nipple (min. 10mm)

ii. Push larger end of supplied drain boot fully over dishwasher nipple.

iii. Push 3/8" tube on supplied drain tube assembly at least 15mm into drain boot. Ensure arrow on drain label is pointing into the drain boot.

iv. Connect 3/16" tube on supplied drain tube assembly to condenser outlet as per Diagram 12. Nut to be finger tightened only.

Option 2: directly to waste trap

i. Drill a 1/2" hole in the side of the waste trap. Hole is to be least 10mm above water level in the trap and on the sink side only.

ii. Clip drain adaptor to drain clamp, ensuring tabs on drain adaptor engage with slots in drain clamp.

iii. Fit drain clamp and adaptor assembly over hole in waste trap. Ensure drain adaptor is oriented with push-fit connection angled up and spigot

pushed into drilled hole.

iv. Tighten drain clamp.

v. Push 3/8" tube on supplied drain tube assembly fully into drain adaptor. Ensure arrow on drain label is pointing into drain adaptor.

vi. Connect 3/16" tube on supplied drain tube assembly to condenser outlet as per Diagram 12. Nut to be finger tightened only

Connect to CO

Cylinder and Regulator

For Billi provided CO

cylinders and regulators follow the below instructions. Otherwise refer to separate attached instructions.

Remove plastic cap from threaded outlet of CO

cylinder.

Check black pressure control knob on CO

regulator is turned fully anti-clockwise (direction of "-" arrow).

Screw CO

regulator onto CO

cylinder and tighten.

i. A small amount of CO

will escape while tightening until fully sealed.

ii. Avoid breathing air containing high levels of CO

or contact with cold escaping gas as per the Material Safety Data Sheet included with the

cylinder.

Connect to CO

regulator to underbench module using supplied black Ø6mm PE tube. Refer to Diagram 10 and 11.

i. CO

cylinder is to be positioned vertically in cabinet.

ii. Trim black Ø6mm PE tube if required and ensure tube is fully inserted.

Connect Main Power Cable

Connect supplied power cable to IEC socket at rear of underbench module and to mains power. DO NOT TURN POWER ON.

Connect Anti-Scale Filter (Optional)

An external anti-scale filter may be fitted in areas where there is high mineral content in the water supply to help prolong service life and reliability.

The Billi OmniOne supports Ø1/4" PE tube connections to external anti-scale filters. To install:

Disconnect both push-fit elbows connected to the scale filter ports on underbench module by pushing demount rings down and pulling fittings up.

i. Bridging tube between the two elbows may also be removed and elbows re-inserted for improved connection angle to anti-scale filter if desired.

Connect anti-scale filter to ports on underbench module, trimming back tubes if required. Refer to Diagram 10 and 11. Ensure tubes are trimmed

square and straight, and are fully pushed in.

Module Rear

Sparkling Flow

rate Adjuster

Condenser

Dispenser

(Black Tube)

(Blue Tube)

Power Cord

Top View

(Installed by plumber)

From Scale

To Scale

Filter

Main Power

Cable

Dispenser

(Grey Tube)

Dispenser

Water

(Red Tube)

Supply

Diagram 10

3/16" Tube

Nut

Stop tap

Push tubing

fully over

shank

Diagram 11

Diagram 12

Installing the Plus Mixer Tap (Billi OmniOne Plus 9 Only)

Components in Plus Mixer Tap Kit

Before commencing installation, identify the following components:

Plus tap assembly with the following fitted:

i. Main tap body with mount thread (brass)

ii. Finished tap base ring

iii. Large o-ring (inset in tap base ring)

iv. Mount clamp gasket

v. Mount clamp plate

vi. Mount clamp (brass)

vii. Locking screws x3 (in mount clamp)

Tube kit containing:

i. Barb adaptor fitting (extended) labelled with "TAP-H" (pre-fitted to tap assembly on some models)

ii. 1 metre PVC tubing

Accessories kit containing:

i. Spring clamps x2

ii. Hex key

iii. Barb adaptor fitting (short)

iv. Aerator key

v. 1/2" BSP inline strainer

vi. 1/2" BSP male coupling

Braided flexible hoses x3:

i. Marked "UNIT HOT-IN"

ii. Marked "TAP-IN"

iii. Marked "TAP-OUT"

Mounting Procedure:

Drill or punch mount hole and deburr.

- Hole size: 35mm

- Sinktop or benchtop thickness: 1 - 45mm

Remove mount clamp gasket and mount clamp plate from mount thread by unscrewing mount clamp.

Screw tap base ring up to base of tap, checking large o-ring is inset in tap base ring.

Screw barb adaptor fitting (extended) labelled "TAP-H" into marked "H" threaded hole in base of tap and tighten.

Insert tap through mount hole and correctly orient tap with Billi Logo facing forwards.

Insert mount clamp gasket followed by mount clamp plate over mount thread from underside of benchtop.

Thread on mount clamp. NOTE: Ensure slot in mount clamp aligns with tabs in mount clamp plate. Refer to Diagram 13..

Firmly hand tighten mount clamp, then use a Philips head screwdriver to tighten all 3 locking screws fitted in the mount clamp.

Screw braided flexible hose marked "TAP-OUT" into marked "OUT" threaded hole in base of tap and tighten.

10. Screw braided flexible hose marked "TAP-IN" into marked "IN" threaded hole in base of tap and tighten.

11. Fully push PVC tube onto barb on the barb adaptor fitting (extended) and secure with supplied spring clamp. Note clamp orientation as per

Diagram 14.

Connecting Mixer Tap to Billi OmniOne Plus

Fit tubing connections as per Diagram 15 and 16.

Separate 1/2" BSP inline strainer from 1/2" BSP male coupling.

Connect braided flexible hose marked "TAP-IN" to water supply inlet with 1/2" BSP inline strainer in between. Use of 1/2" BSP inline strainer

is critical.

Screw barb adaptor fitting (short) to port on Billi OmniOne marked "Hot Outlet".

Trim PVC tubing with a sharp knife to avoid kinking and sagging from excessive length.

i. It is advised to leave 100mm of tubing in addition to minimum required length.

Fit PVC tubing to barb adaptor fitting (short) and secure with supplied spring clamp.

i. Support may be needed for PVC tube if there is a horizontal run.

Fit braided flexible hose marked "UNIT HOT-IN" to port on Billi OmniOne marked "Hot Inlet". Join to braided flexible hose marked "TAP-OUT" using

1/2" BSP male coupling.

Operating the Mixer Tap

Operation of mixer tap is as with any single lever mixer tap. Lift lever to start water flow. Swing lever to adjust water temperature as indicated on lever.

Hot water will not be available until the Billi OmniOne boiling water tank has filled and is heated to temperature. Bubbling in the hot water flow indicates

insufficient boiling water is available. Wait a few minutes in this instance for tank to fill and heat.