- ページ 2

防犯カメラ AVYCON AVC-PHN61FLTのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。AVYCON AVC-PHN61FLT 2 ページ。 Hd network fisheye camera

ページを印刷する

③ Route and connect the cables.

④ Fix the camera to the wall with screws as shown below.

⑤ Install the ﬁxed ring back to the camera.

• Install Camera with Junction Box

① Remove the ﬁxed ring from the gap of the camera (see Install SD Card ①).

② Install the junction box onto the wall

③ Route the cables through the cable hole (take side conduit cabling

for example.) and connect the cables. Then ﬁx the camera onto the junction

box with screws.

④ Install the ﬁxed ring back to ﬁnish the installation.

5. IE Network Connection

Here we take accessing the device via LAN for example. In LAN, there are two

ways to access.

1. Access through IP-Tool;

2. Directly Access through IE Browser

The default network settings are as shown below:

IP address: 192.168.226.201

Subnet Mask: 255.255.255.0

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for the

ﬁrst time.

Switch

Network Cable

IPC

Router

• Access through IP-Tool

2. Directly Access through IE Browser

① Make sure that the camera and the PC are well connected via LAN.

② Find the IP-Tool from the CD and then install it in the computer.

After that, run the IP-Tool as shown below.

Device Network Search

Immediate Refresh

Device Name Device Type

Product Model

IP Address

Http Port

Data Port

name

IPC

unknown

192.168.226.201

9008

name

IPC

unknown

192.168.1.2

9008

name

IPC

unknown

192.168.1.3

9008

Total Device: 3

Local IP Address:192.168.1.4

Subnet Mask:255.255.255.0 Gateway: 192.168.1.1

③ Modify the IP address. The default IP address of this device is 192.168.

226.201. Click the information of the camera listed in the above table to

show the network information on the right hand. Modify the IP address

and gateway of the camera and make sure its network address is in the

same local network segment as that of the computer. Please modify the

IP address of your camera according to the practical situation.

For example, the IP address of your computer is 192.168.1.4. So the IP

address of the camera shall be changed to 192.168.1.X. After modiﬁcation,

please input the password of the administrator and click "Modify" button

to modify the setting. The default password of the administrator is

"123456".

HTTP: 80

Data Port: 9008

④ Double-click the IP address and then the system will pop up the IE

browser to connect IP-CAM. Download the Active X control and run it

in the computer. Then input the user name and password in the login

interface.

Network Cable

Computer

The default username is admin; the default password is 123456.

• Direct Access Through IE

About

① Make sure that the camera and the PC are well connected via LAN.

Subnet

Modify Network Parameter

② Find the IP-Tool from the CD and then install it in the computer.

255.255.

Mac Address

CE :98 :23 :75 :35 :22

255.255.

IP Address

192 .168 . 226 . 201

After that, run the IP-Tool

255.255.

Subnet Mask

255 . 255 . 255 . 0

③ Modify the IP address and make sure its network address is in the

Gateway

192 .168 . 226 . 1

same local network segment as that of the computer.

Modify

④ Open IE browser and input the modiﬁed IP address in the address

Tip: Enter the administrator password, and

then modify the network parameters.

bar to log in the IE client. If it is the ﬁrst time for you to log in, you

Restore IPC Default Configuration

should download the Active X control and run it in the computer.

After that, input the default user name and password to login.

DNS：210.21.196.6

Modify Network Parameter

CE :98 :23 :75 :35 :22

Mac Address

IP Address

192 .168 . 1 . 201

Subnet Mask

255 . 255 . 255 . 0

192 .168 . 1 . 1

Gateway

Modify

Name：

admin

Password：

Stream Type：

1920x1080 25fps

Language：

English

Remember me