- ページ 5

懐中電灯 Miller XT30CのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Miller XT30C 40 ページ。
Miller XT30C にも：マニュアル (40 ページ)

SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING

Protect yourself and others from injury — read, follow, and save these important safety precautions and operating instructions.

1-1. Symbol Usage

DANGER! − Indicates a hazardous situation which, if

not avoided, will result in death or serious injury. The

possible hazards are shown in the adjoining symbols

or explained in the text.

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury. The possible

hazards are shown in the adjoining symbols or ex-

plained in the text.

NOTICE − Indicates statements not related to personal injury.

1-2. Plasma Arc Cutting Hazards

The symbols shown below are used throughout this manual

to call attention to and identify possible hazards. When you

see the symbol, watch out, and follow the related instructions

to avoid the hazard. The safety information given below is

only a summary of the more complete safety information

found in the Safety Standards listed in Section 1-5. Read and

follow all Safety Standards.

Only qualified persons should install, operate, maintain, and

repair this unit.

During operation, keep everybody, especially children, away.

CUTTING can cause fire or explosion.

Hot metal and sparks blow out from the cutting arc.

The flying sparks and hot metal, hot workpiece, and

hot equipment can cause fires and burns. Check

and be sure the area is safe before doing any cutting.

Remove all flammables within 35 ft (10.7 m) of the cutting arc. If this

is not possible, tightly cover them with approved covers.

Do not cut where flying sparks can strike flammable material.

Protect yourself and others from flying sparks and hot metal.

Be alert that sparks and hot materials from cutting can easily go

through small cracks and openings to adjacent areas.

Watch for fire, and keep a fire extinguisher nearby.

Be aware that cutting on a ceiling, floor, bulkhead, or partition can

cause fire on the hidden side.

D Do not cut on containers that have held combustibles, or on closed

containers such as tanks, drums, or pipes unless they are properly

prepared according to AWS F4.1 and AWS A6.0 (see Safety Stan-

dards).

Connect work cable to the work as close to the cutting area as prac-

tical to prevent cutting current from traveling long, possibly unknown

paths and causing electric shock, sparks, and fire hazards.

Do not use plasma cutter to thaw frozen pipes.

Never cut containers with potentially flammable materials inside −

they must be emptied and properly cleaned first.

D Do not cut where the atmosphere may contain flammable dust,

gas, or liquid vapors (such as gasoline).

Do not cut pressurized cylinders, pipes, or vessels.

Wear oil-free protective garments such as leather gloves, heavy

shirt, cuffless trousers, high shoes, and a cap.

Do not locate unit on or over combustible surfaces.

Remove any combustibles, such as a butane lighter or matches,

from your person before doing any cutting.

D After completion of work, inspect area to ensure it is free of sparks,

glowing embers, and flames.

D Use only correct fuses or circuit breakers. Do not oversize or by-

pass them.

D Follow requirements in OSHA 1910.252 (a) (2) (iv) and NFPA 51B

for hot work and have a fire watcher and extinguisher nearby.

Indicates special instructions.

This group of symbols means Warning! Watch Out! ELECTRIC

SHOCK, MOVING PARTS, and HOT PARTS hazards. Consult sym-

bols and related instructions below for necessary actions to avoid the

hazards.

ELECTRIC SHOCK can kill.

Touching live electrical parts can cause fatal shocks

or severe burns. The torch and work circuit are

electrically live whenever the output is on. The input

power circuit and machine internal circuits are also

live when power is on. Plasma arc cutting requires

higher voltages than welding to start and maintain the arc (200 to 400

volts dc are common), but may also use torches designed with safety

interlock systems which turn off the machine when the shield cup is

loosened or if tip touches electrode inside the nozzle. Incorrectly

installed or improperly grounded equipment is a hazard.

Do not touch live electrical parts.

Wear dry, hole-free insulating gloves and body protection.

Insulate yourself from work and ground using dry insulating mats or

covers big enough to prevent any physical contact with the work or

ground.

Do not touch torch parts if in contact with the work or ground.

Turn off power before checking, cleaning, or changing torch parts.

Disconnect input power before installing or servicing this equip-

ment. Lockout/tagout input power according to OSHA CFR

1910.147 (see Safety Standards).

Properly install, ground, and operate this equipment according to its

Owner's Manual and national, state, and local codes.

Check and be sure that input power cord ground wire is properly

connected to ground terminal in disconnect box or that cord plug is

connected to a properly grounded receptacle outlet − always verify

the supply ground.

When making input connections, attach proper grounding conduc-

tor first.

D Keep cords dry, free of oil and grease, and protected from hot metal

and sparks.

Frequently inspect input power cord for damage or bare wiring − re-

place cord immediately if damaged − bare wiring can kill.

Turn off all equipment when not in use.

Inspect and replace any worn or damaged torch cable leads.

Do not wrap torch cable around your body.

Ground the workpiece to a good electrical (earth) ground if required

by codes.

Use only well-maintained equipment. Repair or replace damaged

parts at once.

Wear a safety harness if working above floor level.

Keep all panels and covers securely in place.

Do not bypass or try to defeat the safety interlock systems.

Use only torch(es) specified in Owner's Manual.

Keep away from torch tip and pilot arc when trigger is pressed.

Clamp work cable with good metal-to-metal contact to workpiece

(not piece that will fall away) or worktable as near the cut as

practical.

Insulate work clamp when not connected to workpiece to prevent

contact with any metal object.

pom_2011-10

OM-255 590 Page 1