- ページ 2

池のポンプ Aquatec Equipment AQUAPRO AP2400FのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Aquatec Equipment AQUAPRO AP2400F 5 ページ。 Pond & fountain pump

ページを印刷する

CONGRATULATIONS ON YOUR PURCHASE OF THIS

PRODUCT BY AQUAPRO, THE ANSWERS FOR YOUR

WATERGARDEN MADE EASY.

TECHNICAL SPECIFICATIONS

Description

MAXIMUM WATER FLOW (L/H)

MAXIMUM HEAD (m)

POWER CONSUMPTION* (W)

VOLTS (V)

IP RATING

FREQUENCY (Hz)

INLET Ø BSP FEMALE THREAD

OUTLET Ø BSP FEMALE THREAD

CABLE LENGTH (m)

* SUBJECT TO VARIATION ACCORDING TO LOAD.

BENEFITS

The AQUAPRO Fountain and Pond Pump have been manufactured with advanced technology to provide you with the

best quality pump for your pond or water feature. Check out the AQUAPRO range of pond lights and accessories.

• AQUAPRO Fountain & Pond pumps are suitable for use

in many different applications including fountains and

water features, either submersible or inline.

• AQUAPRO Fountain & Pond pumps are a magnetically

driven centrifugal pump, therefore they cannot suck

from a water level that is below the inlet level when

used inline.

• Your AQUAPRO Fountain & Pond pump has a single

moving part (an impellor set) enabling easy cleaning

and maintenance.

• The motor and electrical components are encapsulated

in epoxy resin, ensuring safe operation under water.

A Q U A T E C E Q U I P M E N T . C O M

AQP AP1000F_AP2400F Instructions.indd 2-3

AP1000F

AP2400F

1200

2600

2.00

2.80

240

IP68

½ INCH

1 INCH

½ INCH

• The pump has a robust bearing and shaft design so no

oil/grease lubrication is required.

• AQUAPRO pumps that have plastic impellor parts and

ceramic shafts, with no exposed metal, can be used in

salt water applications.

• AQUAPRO fountain pumps are fitted with suction

cup feet, enabling use on both horizontal and vertical

surfaces.

• AQUAPRO Fountain & Pond Pumps are continuous

rated therefore are designed to operate 24/7.

AP1000F & AP2400F

POND & FOUNTAIN PUMP

IMPORTANT SAFEGUARDS

Please read the operating instructions and familiarise yourself with the equipment before placing it

in service. Correct and safe use of the system requires strict compliance with the safety instructions.

For safety reasons, persons less than 16 years of age or infirm persons that are not familiar with these

instructions should not use this equipment.

• For your own safety, disconnect from the power supply

before any maintenance of any equipment is attempted

on the tank or water body.

• Be sure the equipment is submerged completely in the

water. The depth should not be greater than 2m.

• Do not operate the pump if the appliance or any

components of the system, such as the power cable,

have been damaged.

• Always use a properly grounded power supply that is

connected to an RCD with a rated residual operating

current not exceeding 30mA. As per AS/NZS

3350.2.41:1997

• The drip loop method should be used to prevent water

from traveling down the cable and onto the plug or

power supply. If the plug does get wet, do not unplug

the cable. Disconnect the circuit breaker that supplies

power to the power supply point. Then unplug and

examine the plug and power supply point for presence

of water. If the power point has become wet, you should

consult an electrician before using the power point

again.

• Always unplug the pump from the power supply when

not in use or before performing any maintenance on the

pump or in the pond. Never pull the cable to disconnect

the plug from the power supply. Grasp the plug and pull

to disconnect.

PRODUCT SPECIFIC SAFEGUARDS

• Do not operate the pump without water at any time, permanent damage may occur.

• Be sure the equipment is submerged completely in the water. The depth should not be greater than 2m.

• Do not operate the pump if the appliance or any components of the system, such as the power cable, have been

damaged.

• The pump is designed to be used in a Garden pond or Aquarium environment. It is not to be used in any other manner

or purpose.

• The pump should only be used in clean water. Do not use the pump in, or with, any chemicals such as a solvent or

gasoline.

• All AQUAPRO Fountain & Pond pumps are water cooled. If the pump flow becomes restricted it will overheat and

could cause permanent damage. The pump needs to be cleaned regularly to prevent the pump becoming blocked,

thus causing the pump to overheat and burn out. This is not a warrantable event.

A Q U A T E C E Q U I P M E N T . C O M

• Use of extension cords outdoors is not recommended.

• If required, have a qualified electrician install a

weatherproof power supply point near to the pond or

water-feature (within the cable length of the appliance).

• Do not install or store the appliance where it will be

exposed to extreme hot or cold temperatures. Do not

use in water above 35°C.

• Do not cut the cable as this will result in voiding your

warranty.

• Care should be taken to arrange the power cable so

that it cannot be accidentally tripped over or pulled.

• Do not attempt to repair the electrical appliance

yourself. Return to an authorized service centre or place

of purchase if a fault occurs, (regular maintenance is not

considered repair and is required by user).

• The power cord cannot be replaced. If the cord is

damaged, the pump must be discarded.

23/10/2015 7:17 AM