コントローラー Epever LandStar LS101240LPLIのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Epever LandStar LS101240LPLI 2 ページ。 Solar charge controller with built in led driver

ページを印刷する

Thank you for selecting the LandStar LPLI series solar charge

controller with built in LED driver. Please read this manual carefully

before using the product and pay attention to the safety

information.

LandStar LPLI Series Solar Charge Controller

1. Overview

The LandStar LPLI series controller combines the solar charge controller and LED

constant current driver into one unit which is ideal for solar LED Lighting, especially for the

application for LED lamp which requires dimmer function. The advanced pulse width

modulation charging methods enables the system charging and discharging management

to obtain the most radical optimization. Make the system cost reduce, and increase the

system flexibility. The features are listed below:

 Apply to lead-acid battery and lithium battery

 Lithium battery self-activating function

 Lithium battery low temperature protection function

 Intelligent power mode with 365-day lighting control technology

 Load reduce power automatically

 Load power limitation function

 Maximum output efficiency of 96%

 Digital precision constant current control and the control accuracy are less than±2%

 Discharging power calculation and real-time energy statistics recording function

 Multiple load control modes, LED rated current and current percentage can be set

 Load test function for detecting the system

 Extensive electronic protections

 Without any button, parameter setting via RC-10 and FC-01 with IR function.

 Fully encapsulated PCB, IP68 protection

 Aluminum housing for better cooling

2. Product Features

❶

Charging Status LED indicator

❷

Battery Status LED indicator

❸

Temperature Sensor

❹

PV Positive and Negative Wires

※Temperature sensor is short circuit or open circuit, the controller will charge or

discharge battery for 25℃ and no temperature compensation.

3. Wiring

 Reference for Serial connection of LED

System Voltage

Serial connection

12V

5～18 LED

24V

10～18 LED

NOTE: The above one LED (1W, 3.3V) is calculated. If the user uses the

unconventional LED, The actual LED voltage must less than the Max.

Load Output Voltage.

WARNING：DO NOT electric shock! The product built-in boost LED driver,

the output voltage is higher than the human safety voltage.

WARNING: If the LED connection number is wrong, the load or controller

is damaged.

 Connection Order

1) Connect components to the charge controller in the sequence as shown above and pay

much attention to the "+" and "-". Please don't insert the fuse or turn on the breaker during

the installation. When disconnecting the system, the order will be reversed.

2) After power on the controller, check the battery LED indicator on the controller, it will be

on solid green. Otherwise please refer to chapter 8.

3) Connecting a fuse in series through battery positive (+) in the circuit and the battery

circuit fuse must be 1.25 to 2 times to the rated current. The installed distance is within

150mm.

 Load self-test function

The load is ON when the controller power on 10seconds. After 10 seconds it will restore to

set working mode.

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

---with built in LED Driver

Figure 1 Product Feature

❺

Battery Positive and Negative Wires

❻

Load Positive and Negative Wires

❼

Infrared Receiver Module

❽

Infrared LED

Min. Output Voltage

Max. Output Voltage

15V

30V

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

4. LED Indicators

Indicator

All

indicators

5. Load Working Mode

1) Manual Mode

2) Light ON/OFF(default)

3) Light ON + Timer

Light ON + Timer1

Light ON + Timer2

60V

Light ON + Timer3

Item

LED Rated Current

Timer1

LED Rated Current Percentage

Timer2

LED Rated Current Percentage

Figure 2 Wiring

Color

Status

Green

On Solid

Green

Slowly Flashing(1Hz)

Green

Fast Flashing(4Hz)

Green

OFF

Green

On Solid

Green

Slowly Flashing(1Hz)

Green

Fast Flashing(4Hz)

Orange

On Solid

Red

On Solid

Red

Slowly Flashing(1Hz)

Green and

Flashing two times

orange

Default※

Mode1

Mode2/3

0.35A

100%

80%

50%

Instruction

PV connection normal

but low

voltage(irradiance) from

PV, no charging

In charging

PV reverse polarity

No PV voltage(night

time) or PV connection

problem

Normal

Full

Over voltage

Under voltage

Over discharged

Battery Overheating

Set parameters

successfully

Range

0-2.6A(LS101240LPLI)

0-2.0A(LS102460LPLI)

0-4.0A(LS101260/2024120LPLI)

00:00—23:59H

0—100%

00:00—23:59H

0—100%