- ページ 2

コントローラー Epever LandStar LS101240LPLIのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Epever LandStar LS101240LPLI 2 ページ。 Solar charge controller with built in led driver

ページを印刷する

Timer3

LED Rated Current Percentage

Timer4/5

LED Rated Current Percentage

Timer6

LED Rated Current Percentage

※The default value can be changed according to the user requirement.

4)Time Control

Control the load on/off time through setting real-time clock.

5) Intelligent Power Mode

When the battery voltage is lower than "Under Voltage Warning Recover Voltage (UVWR

adjustable)", the intelligent power mode is enabled; at this time, the LED current

percentage will be automatically reduced in linear with the voltage drop of battery. When

the battery voltage is lower than "Under Voltage Warning Voltage (UVW adjustable)", a

minimum LED current percentage (default 2%, adjustable) will be output. In addition, when

the battery voltage is higher than UVWR, the controller will exit the intelligent power mode.

NOTE：The load is ON when the controller power on 1seconds. After 1

seconds it will restore to set working mode.

NOTE：In the mode of Light ON/OFF and Light ON/Timer, the load is

turned on after 10Min. delay，the delay time can be set.

6. Setting Operation

There are two methods that it can realize controller work

mode and parameters through IR function:

1) IR Remote Controller—RC-10

2) Super Parameter Programmer—FC-01

This method can realize one-key setting operation which is

suitable for bulk quantity products setting or applied in the

projects.

NOTE: Please refer to the user manual of handheld

device.

7. Protection

Protection

Conditions

PV Reverse

When the battery is correct connecting, the

Polarity

PV can be reversed.

Battery Reverse

When the PV is not connecting, the battery

Polarity

can be reversed.

Battery Over

The battery voltage reaches to the OVD

Voltage

Battery Over

The battery voltage reaches to the LVD

Discharge

Battery

Temperature sensor is higher than 65℃

Overheating

Temperature sensor is less than 55℃

Temperature sensor is less than the low

Libattery Low

temperature value

Temperature

★

Temperature sensor is higher than the low

temperature value

Load current ≥2.5 times rated current

One short circuit, the output is OFF 5s;

Two short circuit, the output is OFF 10s;

Load Short

Three short circuit, the output is OFF 15s;

Circuit

Four short circuit, the output is OFF 20s;

Five short circuit, the output is OFF 25s;

Six short circuit, the output is OFF

Max. load voltage≥68V

One open circuit, the output is OFF 5s;

Two open t circuit, the output is OFF 10s;

Load Open

Three open circuit, the output is OFF 15s;

Circuit(Load over

Four open circuit, the output is OFF 20s;

voltage)

Five open circuit, the output is OFF 25s;

Six open circuit, the output is OFF 5s;

Seven open circuit, the output is OFF 5s

★ WARNING: If selecting a lithium battery, it must be set low temperature

value(LTV) according to the charging/ discharging temperature of lithium

battery; otherwise, the lithium battery will be damaged.

8. Troubleshooting

Faults

Possible reasons

Charging LED

indicator off during

daytime when

array disconnection

sunshine falls on PV

modules properly

Min.9V can start up the

No LED indicator

controller.

Battery LED

indicator green Fast

Battery over voltage

Flashing

Battery

Battery LED

indicator red

over discharged

Battery Status LED

indicator red

Battery Overheating

flashing

All the LED indicator

System voltage error

flashing(battery red

BEIJING EPSOLAR TECHNOLOGY CO., LTD.

00:00—23:59H

50%

0—100%

00:00—23:59H

0—100%

00:00—23:59H

100%

0—100%

Status

The controller is not

damage

Stop charging

Stop discharging

Output is OFF

Output is ON

Stop charging or

discharge

Begin charging or

discharge

Output is OFF

Clear the fault:

Restart the controller

or wait for one

night-day cycle

(night time>3 hours).

Output is OFF

(Cycle to perform)

Troubleshooting

Confirm that PV and battery wire

connections are correct and tight

Measure battery voltage with

multi-meter. Min.9V can start up the

controller.

①Disconnect the solar array and

measure the battery voltage whether

is too high; ②Change the controller;

③ Change the battery

When the battery voltage is restored

to or above setpoint (low voltage

①

reconnect voltage), the load work

The controller will automatically stop

working. When the temperature is

below 50 º C, the controller will resume

to work.

Check whether the battery voltage

match with the controller working

Tel：+86-10-82894112 / 82894962 Website：www.epsolarpv.com/www.epever.com

indicator flashing)

①The connecting

wires are error or

virtual connection

Powering on

②Load mode is wrong

normally, the load is

③The controller does

off

not match with the LED

light.

④Output short circuit

The controller does not

match with the LED

light source. This

The dimming

product is a step-up

function is invalid

current control, If input

voltage is lower than

the rated voltage, it is

not working.

①When the battery is over discharged, the battery indicator will be red and the load will be off

all the time before the voltage is more than the Low Voltage Reconnect Voltage (LVRV). In

order to judge the system is normal or not, firstly measuring the battery voltage whether is

more than LVRV, if not, restarting the controller to detect the load whether it is normal.

WARNING: The LVRV can be set, but it must pay more attention that it

maybe damages the battery if the LVRV is too low.

9. Technical Specifications

Models

LS101240LPLI

Item

Nominal system

voltage

Rated charge current

10A

Max. PV open circuit voltage

Battery input voltage range

Max. output power

40W

Max. output Current

2.6A

Output voltage range

Load open circuit voltage

Maximum output efficiency

Output current

control accuracy

Lead-acid battery: Sealed(default)/Gel/Flooded/User

Battery Type

Lithium battery:LiFePO4/Li-NiCoMn/User

Equalization Voltage▼

Sealed:14.6V; Flooded:14.8V;User:9-17V

Boost Voltage▼

Sealed:14.4V;Gel:14.2V;Flooded:14.6V;User:9-17V

Float Voltage▼

Sealed/Gel/Flooded：13.8V;User：9-17V

Low Voltage

Sealed/Gel/Flooded：12.6V;User：9-17V

Reconnect Voltage▼

Under Voltage Warning

Sealed/Gel/Flooded：12.2V;User：9-17V

Recover Voltage▼

Under Voltage Warning

Sealed/Gel/Flooded：12.0V;User：9-17V

Voltage▼

Low Voltage Disconnect

Sealed/Gel/Flooded：11.1V;User：9-17V

Voltage▼

Boost Voltage▼

LiFePO4(4s):14.5V/Li-NiCoMn(3s):12.5V/User:9-17V

Low Voltage

LiFePO4(4s):12.8V/Li-NiCoMn(3s):10.5V/User:9-17V

Reconnect Voltage▼

Under Voltage Warning

LiFePO4(4s):12.8V/Li-NiCoMn(3s):12.2V/User:9-17V

Recover Voltage▼

Under Voltage Warning

LiFePO4(4s):12.0V/Li-NiCoMn(3s):10.5V/User:9-17V

Voltage▼

Low Voltage Disconnect

LiFePO4(4s):11.1V/Li-NiCoMn(3s):9.3V/User:9-17V

Voltage▼

Self-consumption

Charge Circuit Voltage Drop

Com. way

Com. distance of IR

Working environment

temperature

Enclosure

Overall dimension(mm)

87x58x22.8

Mounting dimension(mm)

Mounting hole size(mm)

Power cable

Net weight

0.18kg

◆The controller is not recognize system voltage and no temperature compensation

when the battery connect the lithium battery.

▼The parameters are 12V system at 25 º C, please double the values in 24V system.

10. Disclaimer

This warranty does not apply under the following conditions:

 Damage from improper use or use in an unsuitable environment.

 PV or load current, voltage or power exceeding the rated value of controller.

 The controller is working temperature exceed the limit working environment

temperature.

 User disassembly or attempted repair the controller without permission.

 The controller is damaged due to natural elements such as lighting.

 The controller is damaged during transportation and shipment.

Any changes without prior notice!

voltage. Please change to a suitable

battery or reset the working voltage

①Check the connecting cables

②Check the load mode and

parameter

③The voltage of LED light source is

not in the output voltage range of

controller

④Check the connecting cables and

LED light source

①Replace the LED light

②Reduce system rated voltage grade

and replace the product model

For example 24V system change to

12V system, and replace the

corresponding controller.

LS101260LPLI

LS102460LPLI

12VDC

12/24VDC◆

10A

30V

50V

9～16V

9～32V

30W/12V

60W

60W/12V;120W/24V

60W/24V

4.0A

2.0A

(Max. Battery Voltage +2V)～60V

60V

96%

≤2%

≤18mA(12V);≤23mA(24V)

≤0.14V

≤6m

-40℃～+55℃

IP68(1.5m,72h)

87x63x24.8

108.5x118x25.6

Φ4

PV/BAT:14AWG/2.5mm

PV/BAT:12AWG/4.0mm

LOAD: 18AWG/1.0mm

LOAD:18AWG/1.0mm

0.21kg

Version number：V1.8

LS2024120LPLI

20A

4.0A

100.5x76

Φ5

0.40kg