- ページ 17

試験装置 AccuPulse NIBP SimulatorのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。AccuPulse NIBP Simulator 20 ページ。 Hand held nibp simulator

ページを印刷する

Using Commands

The remote-control user of an ApHandheld utilizes the following command to enable

remote-control:

<> <CR>

In response to this, the user should see the message:

<USB_MULTICHAR_CMDS_ENABLED>

The first line returned is a comment to the user "<USB...>" which indicates the

command parser is awake.

The '=' indicates the command was recognized and hence was executed successfully.

The '>' is the prompt char, indicating the unit is waiting for another command.

Argument versus Argument-less commands

Commands that take arguments give their arguments Carriage-return delimited from

the command. Where this documentation shows arguments in braces

[argument1,argument2] it is listing acceptable variables. These are to be entered

without the braces.

Sent:

< ARGUMENT_COMMAND > <CR>

ARGUMENT1 <CR>

Received:

= <CR> --OR--

Sent:

< ARGUMENT_LESS_COMMAND > <CR>

Received:

= <CR> --OR-

Note: Synch on the '>' character (prompt character) to indicate a

command completed. The previous line in the stream will have the result

of the operation ('=', '*', etc).

Commands

Start Remote Control:

Send:

<> <CR>

Recv:

<USB_MULTICHAR_COMMS_STARTED> <CR>

= <CR>

Keypad Disable / Enable Commands

Send: <KEYPAD_OFF> <CR> --OR--

Recv: '=' <CR>

Use of this is highly recommended. These commands turn processing of the physical

keypad off/on so that the user does not have to worry about keypad inputs interfering

with the execution of a remote control session.

(error code if error occurred) <CR>

<KEYPAD_ON> <CR>

Help

This command returns a listing of available commands in the current software.

These may vary based upon the configuration options loaded in the unit.

Send:

<HELP>

Recv:

Available Remote Commands:

<TEST_MODE>

<SET_SHFT>

<SET_PRESET>

<SET_PR>

<SET_DEVICE_ID>

<SET_AMP>

<SETP_CFG>

<MAN_STR>

<MAN_SMP>

<LEAK_CFG>

<KEYPAD_ON>

<KEYPAD_OFF>

<I>

<HEX_SCREENSHOT>

<HELP>

<GET_SERIAL_NUM>

<GET_FEATURES>

<GET_DEVICE_ID>

<GET_CALTABLE>

<GET_BP_PARAMS>

<BIN_SCREENSHOT>

Virtual Button Press

This provides a way to push the front panel buttons by remote control. All operations can

always be controlled in this way. In some cases a direct remote control command is also

provided as a shortcut to perform a certain task.

Send:

KEYNAME <CR>

Recv: '=' – Success

'*' – key blocked this mode (keypad is off)

'#' – bad key name

Key Names:

All handhelds: F1,F2,F3,F4,UP ,DWN,LEFT,RIGHT,MENU

Generic Keypad: ESC, ENTER, SCROLL_UP , SCROLL_DOWN

Fixed Keypad: BP ,LEAK,OVERP ,METER

Selecting Test Mode

Set Test Mode

Send: <TEST_MODE> <CR>

[BP , LEAK, OVERP , SETP] <CR>

Recv: '=' – success

Setting Test Parameters

Set BP Mode

BP_MODE is the default "Preset" mode included in all NIBP units.

UTP_MODE is the optional User Defined Test Points software module.

Send:

<SET_BP_MODE> <CR>

[BP_PRESET,UTP_MODE] <CR>

Recv:

'=' – success

'#' – invalid mode name.