- ページ 2

アンプ Axxess CHTO-013のPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。Axxess CHTO-013 2 ページ。 Chrysler can bus interface

ページを印刷する

APPLICATIONS

CHRYSLER

NITRO 2007-10*

300 2008-10

RAM 1500 2009-2010

ASPEN 2008-09

RAM 2500/3500 2010

SEBRING 2007-10*

JEEP

TOWN & COUNTRY 2008-10*

COMMANDER 2006-2007

DODGE

COMPASS 2007

AVENGER 2008-10*

GRAND CHEROKEE 2005-2007

CALIBER 2007

PATRIOT 2007

CHALLENGER 2009-10

WRANGLER 2007-10*

CHARGER 2008-10

DAKOTA 2008-09

DURANGO 2008-09

GRAND CARAVAN 2008*

JOURNEY 2009-10*

MAGNUM 2008

*NOTE: THE CHTO-013 COMES WITH 2 DIFERENT CHRYSLER 22 PIN HARNESSES. THE

APPLICATIONS WITH A (*) USE THE BIGGER OF THE TWO HARNESSES. THE BIGGER OF

THE TWO HARNESSES ALSO HAVE 2 LARGER TERMINALS, ONE AT EACH END OF THE

CONNECTOR.

NOWLEDGE IS

Enhance your installation and fabrication skills by

enrolling in the most recognized and respected

mobile electronics school in our industry.

Log onto www.installerinstitute.com or call

800-354-6782 for more information and take steps

toward a better tomorrow.

Metra recommends MECP

certified technicians.

WIRING UP THE CHTO-013

* Important: Before beginning any of the following, disconnect the negative

battery terminal to prevent accidental short circuit.

* * NOTE: THE ACCESSORY POWER SOURCE OF MOST ALL CHRYLSER VEHICLES KEEPS

THE RADIO ON UNTIL ONE OF THE DOORS IS OPENED. THIS IS CALLED R.A.P.

(RETAINED ACCESSORY POWER). THE CHTO-013 IS DESIGNED TO RETAIN THIS FEA-

TURE.

* NOTE: THE VEHICLES IGNITION SWITCH MUST BE IN THE OFF POSITION BEFORE

PLUGGING THE CHTO-013 MODULE IN. ALSO THE KEY MUST BE CYCLED AT A MEDIUM

PACE AT LEAST TWO TIMES BEFORE BEGINNING TESTING.

CONNECTIONS TO BE MADE ON THE 22

PIN HARNESS:

1. Connect the yelow wire to the radio's 12v battery or memory wire.

2. Connect the black wire to the radio's ground wire.

3. Connect the orange wire to the radio's illumination wire. If wire is not present,

tape up wire.

4. For the Caliber only, connect the blue/white wire to the blue/white wire in

the 14 pin harness, which connects to the radio's amplifier turn-on wire.

OWER

CHTO-013

CONNECTIONS TO BE MADE ON THE 14

PIN HARNESS

1. Connect the blue/white wire to the radio's amplifier turn-on wire.

2. Connect the red wire to the radio's Igniton or accessory wire.

3. Connect the RCA cables to the radio's RCA outputs. If no RCA outputs are

available, use the Metra line output converter, part # ALOC648,

(SOLD SEPARATELY).

4. The white RCA goes to the left front RCA output of the radio.

5. The gray RCA goes to the right front RCA output of the radio.

6. The green RCA goes to the left rear RCA output of the radio.

7. The purple RCA goes to the right rear RCA output of the radio.

The following wires on the 14 pin harness are for the aftermarket radios

that have navigation built in:

Connect the Brown wire to the mute wire of the aftermarket radio.

Connect the Green wire to the parking brake wire of the aftermarket radio.

Connect the Blue/Pink wire to the VSS or speed sense wire of the aftermarket

`radio.

Connect the Green/Purple wire to the reverse wire of the aftermarket radio.

• When completed, plug the 14 pin harness into the CHTO-013.

INSTALLING THE CHTO-013

1. With all connections completed to the aftermarket radio, plug the 22 pin

connector into the vehicles corresponding wiring harnesses.

2. Cycle the key by turning the ignition on then back off, then back on again

to test the radio.

TESTING THE CHTO-013

1. Turn the ignition on then the radio to verify the radio works. Check balance

and fader controls for proper operation. If controls are backwards, check to

see if the RCA's are in the correct location.