- ページ 2

屋外ライト CREE LIGHTING IG SeriesのPDF インストレーション・インストラクションをオンラインで閲覧またはダウンロードできます。CREE LIGHTING IG Series 3 ページ。 Led luminaire
CREE LIGHTING IG Series にも：インストレーション・インストラクション (2 ページ)

ページを印刷する

CREE LIGHTING IG Series インストレーション・インストラクション

Mounting

Plate

(4) Luminaire Slots

Luminaire

Slots

STEP 3:

Make wiring connections per "Electrical

Connections" section.

STEP 4:

After wiring connections have been made,

tuck all wires into junction box ensuring that

no wires are pinched. For luminaires with

wireform remove wireform on luminaire

from the clip on the mounting plate. Fold the

wireform back down onto the luminaire.

STEP 5:

Attach luminaire to the Mounting Plate by

pressing up on the luminaire until the slots

on the luminaire engage with the clips on

the Mounting Plate and rotate until clips lock

securely. To secure install a minimum of (2)

supplied screws across from each other into

the mounting plate clips on the underside of

the luminaire. See Figure 5.

NOTE: Installation may require extra pressure

on luminaire to engage clips into slots. Only

apply pressure on housing body NOT on the

luminaire lens.

NOTE: If the mounting plate clips become

deformed during installation, slightly reopen

the clips back up using a screwdriver to ensure

proper install of luminaire.

STEP 6:

Lightly pull on the luminaire to verify luminaire

is securely mounted.

FIXTURE SERVICING AND

MAINTENANCE

STEP 1:

If supply wiring splices need to be inspected

or if luminaire needs to be removed, fully

loosen the (2) screws and rotate luminaire to

disengage from Mounting Plate.

NOTE: For luminaires with wireform, locate

wireform on luminaire and attach it to

mounting plate to support luminaire during

splice inspection. See Figure 4.

2 of 3

(4) Clips

View of Underneath

(2) Screws

Luminaire

(4) Mounting

Plate Clips

STEP 2:

To re-install luminaire, when finished with

servicing or maintenance follow Step 2-6 in

"Junction Box Mounting" section above.

PENDANT MOUNTING (OPTIONAL)

NOTE: Customer supplied 3/4" IP Pendant

Kit and wire leads may be necessary for

pendant mounting. For existing rigid pendant

installations, perform Step 2 through 8

only. Not recommended for use with a hang

straight pendant. Cree does not provide a

counterbalance system.

NOTE: "J" Input Power Designator comes with

safety cable only. "A" Input Power Designator

comes with a safety cable or wireform.

STEP 1:

Feed wire leads through customer supplied

pendant kit. See Figure 6. Make sure leads are

at least 6 in longer than customer supplied

pendant stem.

STEP 2:

WITH SAFETY CABLE ( A or J Input Power

Designator)

Locate the safety cable on the luminaire and

attach the cable to the designated screw hole

on the Pendant Mounting Plate using the

provided screws. See Figure 1 and 3.

WITH WIREFORM ( A Input Power Designator)

Luminaries with wireform go to Step 3.

STEP 3:

WITH SAFETY CABLE ( A or J Input Power

Designator)

NOTE: Two people may be needed for installing

to customer supplied pendant kit, one to

hold the luminaire and another to install the

Pendant Mounting Plate to the customer

supplied pendant kit.

Attach Pendant Mounting Plate to customer

supplied pendant kit. See Figure 6.

Wireform

Pendant Kit

(Supplied by

Customer)

Safety Cable

Pendant Mounting

Plate

Water Shield

Luminaire

WITH WIREFORM ( A Input Power Designator)

Attach Pendant Mounting Plate to customer

supplied pendant kit. See Figure 6.

STEP 4:

Feed wire leads through the Water Shield.

NOTE: Water Shield will be held in place by

the Pendant Mounting Plate. No fasteners are

necessary.

STEP 5:

For luminaires with Wireform, If wiring to a

previously installed pendant kit, locate the

wireform on luminaire and attach it to the clip

on the Pendant Mounting Plate for hands-free

wiring. See Figure 7.

STEP 6:

Make wiring connections to customer supplied

wire leads per "Electrical Connections"

section.

STEP 7:

After wiring connections have been made, tuck

all wires into the water shield ensuring that no

wires are pinched. If used, remove wireform

on the luminaire from the clip on the pendant

Mounting Plate. Fold wireform back down onto

luminaire.

NOTE: Ensure that splices are contained within

Water Shield for future splice inspections.

STEP 8:

Attach luminaire to the Pendant Mounting

Plate by engaging the clips on the Pendant

Mounting Plate with the slots on the luminaire.

Rotate until clips lock securely. See Figure 7.

NOTE: May require extra pressure on Pendant

Mounting Plate to engage luminaire clips into

slots.

STEP 9:

Install a minimum of (2) supplied screws

into the pendant mounting plate clips on the

underside of the luminaire. See Figure 7.

LPN00305X0001A5_B