- ページ 4

池のポンプ Fiap Aqua Active PlusのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Fiap Aqua Active Plus 20 ページ。

ページを印刷する

FIAP Aqua Active Plus

Information about this operating manual

Please read the operating instructions and familiarise yourself with the unit prior to using it for the first

time. Adhere to the safety information for the correct and safe use of the unit.

Please keep these operating instructions in a safe place! Also hand over the operating instructions

when passing the unit on to a new owner. Ensure that all work with this unit is only carried out in

accordance with these instructions.

Intended use

The FIAP Aqua Active Plus series, in the following termed unit, is a filter unit with integrated UVC

clarifying unit for cleaning normal pond water at a water temperature of +4 to +35 °C. The unit is

exclusively intended for private use and may only be employed in ponds with or without fish population.

The use in swimming ponds is forbidden.

Use other than that intended

Danger to persons can emanate from this unit if it is not used in accordance with the intended use and

in the case of misuse. If used for purposes other than that intended, our warranty and operating permit

will become null and void.

CE Manufacturer's Declaration

We declare conformity in the sense of the EC directive, EMC directive (89/336/EEC) as well as the low

voltage directive (73/23/EEC). The following harmonised standards apply:

EN 55015, EN 60335-1, EN 60335-2-41, EN 55014-2, EN 61000-3-2, EN 61000-3-3

Safety information

For safety reasons, children and young persons under 16 years of age as well as persons who

cannot recognise possible danger or who are not familiar with these operating instructions, are

not permitted to use the unit!

The combination of water and electricity can lead to danger to life and limb, if the unit is incorrectly

connected or misused. Do not operate the unit if persons are in the water! Always disconnect the

power plugs from all units in the water and from this unit prior to reaching into the water and starting

work on the unit! Compare the electrical values of the power supply with those on the type plate on the

packaging or on the unit itself. Only operate the unit when plugged into an earthed socket. The latter

must have been installed in accordance with the valid national regulations. Ensure that the protective

earth wire is led to the unit. Only use electrical equipment, adapters, extension or connection cables

with an earthed contact which are approved for outside use. The cross section of power connection

cables must not be smaller than the rubber cables identified with H05-RNF. Extension cables must

meet DIN VDE 0620. Ensure that the unit is fused for a rated residual current of max. 30 mA via a

residual current-operating system (FI or RCD resp.). Keep the power plug and all connection points

dry! Protect the connection cable when burying to avoid

damage. Electrical installations at garden ponds must meet the international and national regulations

valid for installers. Do not carry or pull the unit by the connection cable! Never operate the unit if the

cable or housing are defective! Dispose of the entire unit if the cable is damaged, as the latter cannot

be replaced individually. Never open the unit or its component parts, unless this is explicitly mentioned

in the operating instructions. Never carry out technical changes to the unit. Only use spare parts

meeting the quoted specifications and original accessories. Only allow FIAP

authorised customer service outlets to perform repairs. For your own safety, consult a qualified

electrician if you have questions or encounter problems!

Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045

FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen

Tel: 09628 9213 0; Fax: 09628 9213 30;

www.fiap.com

FIAP Aqua Active Plus

Attention! Dangerous ultra-violet radiation.

The radiation of the UVC lamp, even in small doses, is dangerous for eyes and skin! Never operate the

UVC lamp in a defective housing or outside of the housing.

Assembly and installation

Opening the filter housing: Pull the clamps on both sides of the bottom strainer casing to the side and

lift off the top strainer casing.

Set-up the unit

Place the unit in the pond on a horizontal, firm and sludge free ground and ensure that it is completely

covered by water.

Inserting the nozzle tube

Pull the nozzle tube to the desired length. Undo the clamping screw, vertically align the nozzle tube

and fasten the clamping screw hand tight.

Adjust the fountain height by means of the regulator. Set the water quantity for the second connection

point by means of the regulator.

Switching on / switching off

Attention! Dangerous electrical voltage.

If cables or components are defective, unit components and pond water can carry dangerous electrical

voltage.

Possible consequences: Death or severe injury by electrocution.

Protective measures: Disconnect the power plug prior to reaching into the water and commencing

work.

Never operate the unit without water or without pump filter!

In the event of overheating, a fitted temperature monitor switches the UVC lamp off automatically, the

lamp automatically switches on again once it has cooled down.

The unit switches on automatically when power connection is established.

Switching on: Plug the power plug into the socket.

Switching off: Disconnect the power plug.

Cleaning and maintenance, changing the UVC lamp

Attention! Dangerous electrical voltage.

If cables or components are defective, unit components and pond water can carry dangerous electrical

voltage.

Possible consequences: Death or severe injury from electrocution.

Protective measures: Disconnect the power plug prior to reaching into the water and commencing

work.

Opening the filter housing

Unscrew the stepped hose adapter prior to removing the branch valve. Pull the clamps on both sides

of the bottom strainer casing to the side and lift off the top strainer casing. Remove the UVC clarifying

unit including pump. Clean the bottom strainer casing and the top strainer casing with clear water using

a brush.

Technische Änderungen vorbehalten. Für Druckfehler übernehmen wir keine Haftung. WEEE-Reg. Nr.: DE78152045

FIAP GmbH, Jakob Oswald Str. 16, 92289 Ursensollen

Tel: 09628 9213 0; Fax: 09628 9213 30;