プリンター Epson Іендгі C43 seriesのPDF ここからスタートをオンラインで閲覧またはダウンロードできます。Epson Іендгі C43 series 2 ページ。
ページを印刷するStart Here
EPSON Stylus
C43 Series
®
Read these instructions before using the printer.
1
Unpack
1
Remove the tape and packing material from the printer.
2
Open the cover. Then peel off the tape and remove the insert. Do not
touch or remove the white cable inside the printer.
Remove
insert
Do not touch
or remove the
white cable
3
Insert the paper support into the three slots on the back of the printer.
2
Power On
1
Find the power cord that came in the box and connect
one end to the printer.
2
Plug the other end into a grounded electrical outlet.
3
Press down firmly on the
power button until the green
power light
comes on.
Power button
Caution: Use only the printer's
power button to turn the printer
on or off.
3
Load Ink
Note: The ink cartridges that came with your printer have a lower yield
due to the ink loading process. This process is carried out the first time
you turn on your printer and guarantees a better performance.
Caution: Keep ink cartridges out of the reach of children and do not
drink the ink.
1
Open the printer cover.
Caution: Don't touch the sensor behind
the ink cartridge holders.
2
Lift up the ink cartridge clamps.
3
Unpack the ink cartridges that
came with your printer and
remove the yellow tape only.
Don't touch the green part
4
Insert both cartridges.
Color
Black
Caution: You must install both
cartridges or the printer won't work.
5
Press down on the cartridge clamps
until they click shut.
6
Press the
maintenance
button. The green
power light
Maintenance
flashes and you hear the printer
button
charge its ink.
7
Close the printer cover. When
the green
power light stops
flashing, charging is done.
Caution: Never turn off the printer
while the green
power
light is flashing, or you'll waste ink.
4
Connect the Printer
Note: Turn off your computer before connecting the interface cable.
Don't turn on your computer until you are instructed to do so.
Printer cables are not included with your printer. You need only one of the
following cables:
®
®
•
USB cable (Windows
or Macintosh
) or
•
Parallel cable (Windows only)
Note: If you have Windows 95, you must use a parallel cable.
continue
USB Cable Users (Windows or Mac
®
)
1
Make sure your computer is turned off. Keep it turned off until
section 6, "Install Software." (Click Start and select your Shut Down
or Turn Off option.)
2
Plug the
square end of the cable into the USB port on
your printer.
3
Plug the
flat end of the cable into any available USB port
on your computer.
Flat end
Square end
Parallel Cable Users (Windows only)
1
Make sure your computer is turned off. Keep it turned off until
section 6, "Install Software." (Click Start and select your Shut Down
or Turn Off option.)
2
Plug the end of the cable with the slotted connector into the parallel
port on the side of the printer, then secure it with the wire clips.
3
Plug the end of the cable with the screws on the side into your
computer's parallel port and secure it.
End with screws
Slotted end
5
Load Paper
1
Set some paper behind the tab on the right edge guide. Don't force it in.
2
Press in the locking tab on the left edge guide and slide it against
the paper.
3
Pull out the output tray.
Note: If you're using special EPSON
®
paper, make sure you load
the brighter, whiter side face up.
6
Install Software
Windows
1
Make sure your printer is connected and turned on, then turn
on your computer.
2
When you see the Found New Hardware Wizard screen, click Cancel.
(If you're using a parallel cable, you may not see this screen until later.)
Click Cancel
3
Insert the printer software CD-ROM in your CD-ROM or DVD drive.
If you see any other Windows screens, close or cancel them.
4
The installer starts automatically. Select English. If the language
selection screen doesn't appear, do the following:
Windows XP: Click Start, then click
My Computer. Double-click
the EPSON CD-ROM icon, then double-click the EPSON icon.
Other Windows systems: Double-click
My Computer. Double-click
the EPSON CD-ROM icon, then double-click the EPSON icon.
5
You see the license agreement. Read the license agreement
and click Agree.
6
You see the Main Menu.
Click Install Printer Driver and
follow the on-screen instructions.
Note: If you see a screen asking you to turn on the printer, make sure
the printer is connected and turned on and wait for the computer
to detect the printer port.
7
At the end of the installation, click OK.
8
Click on Install Optional Software.
Select the software you want to
install and follow the on-screen
instructions.
9
When you're done, click Back to return to the Main Menu.
10
Click on Install User's Guide, then follow the on-screen instructions
to install the printer manual on your desktop.
Note: You need a browser—such as Microsoft
®
Internet Explorer 4.0
or later or Netscape
®
4.0 or later—to view the guide.
11
Click on Register your EPSON Printer to register your printer online.
When you're done, close your browser and click Exit on the Main
Menu to close the installation program and remove the EPSON CD.
You're ready to print! See your electronic User's Guide for details.
Turn over