Epson Іендгі C43 series Почніть звідси.

Переглянути онлайн або завантажити pdf Почніть звідси. для Принтер Epson Іендгі C43 series. Epson Іендгі C43 series 2 сторінки.

Друкувати сторінку

Start Here

EPSON Stylus

C43 Series

Read these instructions before using the printer.

Unpack

Remove the tape and packing material from the printer.

Open the cover. Then peel off the tape and remove the insert. Do not

touch or remove the white cable inside the printer.

Remove

insert

Do not touch

or remove the

white cable

Insert the paper support into the three slots on the back of the printer.

Power On

Find the power cord that came in the box and connect

one end to the printer.

Plug the other end into a grounded electrical outlet.

Press down firmly on the

power button until the green

power light

comes on.

Power button

Caution: Use only the printer's

power button to turn the printer

on or off.

Load Ink

Note: The ink cartridges that came with your printer have a lower yield

due to the ink loading process. This process is carried out the first time

you turn on your printer and guarantees a better performance.

Caution: Keep ink cartridges out of the reach of children and do not

drink the ink.

Open the printer cover.

Caution: Don't touch the sensor behind

the ink cartridge holders.

Lift up the ink cartridge clamps.

Unpack the ink cartridges that

came with your printer and

remove the yellow tape only.

Don't touch the green part

Insert both cartridges.

Color

Black

Caution: You must install both

cartridges or the printer won't work.

Press down on the cartridge clamps

until they click shut.

Press the

maintenance

button. The green

power light

Maintenance

flashes and you hear the printer

button

charge its ink.

Close the printer cover. When

the green

power light stops

flashing, charging is done.

Caution: Never turn off the printer

while the green

power

light is flashing, or you'll waste ink.

Connect the Printer

Note: Turn off your computer before connecting the interface cable.

Don't turn on your computer until you are instructed to do so.

Printer cables are not included with your printer. You need only one of the

following cables:

•

USB cable (Windows

or Macintosh

) or

•

Parallel cable (Windows only)

Note: If you have Windows 95, you must use a parallel cable.

continue

USB Cable Users (Windows or Mac

)

Make sure your computer is turned off. Keep it turned off until

section 6, "Install Software." (Click Start and select your Shut Down

or Turn Off option.)

Plug the

square end of the cable into the USB port on

your printer.

Plug the

flat end of the cable into any available USB port

on your computer.

Flat end

Square end

Parallel Cable Users (Windows only)

Make sure your computer is turned off. Keep it turned off until

section 6, "Install Software." (Click Start and select your Shut Down

or Turn Off option.)

Plug the end of the cable with the slotted connector into the parallel

port on the side of the printer, then secure it with the wire clips.

Plug the end of the cable with the screws on the side into your

computer's parallel port and secure it.

End with screws

Slotted end

Load Paper

Set some paper behind the tab on the right edge guide. Don't force it in.

Press in the locking tab on the left edge guide and slide it against

the paper.

Pull out the output tray.

Note: If you're using special EPSON

paper, make sure you load

the brighter, whiter side face up.

Install Software

Windows

Make sure your printer is connected and turned on, then turn

on your computer.

When you see the Found New Hardware Wizard screen, click Cancel.

(If you're using a parallel cable, you may not see this screen until later.)

Click Cancel

Insert the printer software CD-ROM in your CD-ROM or DVD drive.

If you see any other Windows screens, close or cancel them.

The installer starts automatically. Select English. If the language

selection screen doesn't appear, do the following:

Windows XP: Click Start, then click

My Computer. Double-click

the EPSON CD-ROM icon, then double-click the EPSON icon.

Other Windows systems: Double-click

My Computer. Double-click

the EPSON CD-ROM icon, then double-click the EPSON icon.

You see the license agreement. Read the license agreement

and click Agree.

You see the Main Menu.

Click Install Printer Driver and

follow the on-screen instructions.

Note: If you see a screen asking you to turn on the printer, make sure

the printer is connected and turned on and wait for the computer

to detect the printer port.

At the end of the installation, click OK.

Click on Install Optional Software.

Select the software you want to

install and follow the on-screen

instructions.

When you're done, click Back to return to the Main Menu.

Click on Install User's Guide, then follow the on-screen instructions

to install the printer manual on your desktop.

Note: You need a browser—such as Microsoft

Internet Explorer 4.0

or later or Netscape

4.0 or later—to view the guide.

Click on Register your EPSON Printer to register your printer online.

When you're done, close your browser and click Exit on the Main

Menu to close the installation program and remove the EPSON CD.

You're ready to print! See your electronic User's Guide for details.

Turn over