- ページ 7

洗濯機 Siemens IQ500のPDF 取付・使用説明書をオンラインで閲覧またはダウンロードできます。Siemens IQ500 16 ページ。
Siemens IQ500 にも：ユーザーマニュアル (27 ページ), 取付説明書 (20 ページ), 取付説明書 (19 ページ)

ページを印刷する

Control panel model 3

Control panel

Explanation

Fan on/off

Light on/off/dimming

Reduce the fan settings

Increase the fan settings/intensive setting 1, 2

Boost function (short-term maximum power)

Automatic mode with fan run-on time

Setting the fan

Switching on the appliance

Press the

button.

■

The fan starts at setting

Press the + or - button to change the fan strength.

■

Switching off

Press the

button.

Intensive setting

You can use the intensive setting if there is a large build-up of

odours and fumes/vapours.

Press the + button when the fan is at setting

The intensive setting

is activated. Pressing the + button

2‚

again activates the intensive setting

After approx. six minutes, the electronics automatically reduce

the fan to a lower setting . If you want to end the intensive

setting before the preset time expires, press the - button until

the required fan setting is reached.

Boost function

The boost function is a short-term maximum power setting

which can be activated in any fan setting.

Press the

button. After approx. 20 seconds, the fan switches

back to the previously set fan setting.

Automatic mode

Switching on the appliance

Press the

button.

■

The fan starts at

setting.

Press the

button.

■

The optimum fan setting

sensor.

Switching off the appliance

Press the

button to switch off automatic mode.

The fan switches off automatically if the sensor no longer

detects a change in the air quality of the room.

The automatic mode lasts 4 hours at most.

„

2 ƒ

is automatically set via a

‚

„

Sensor control

In automatic mode, a sensor in the extractor hood detects the

intensity of the cooking and roasting fumes. Depending on the

setting of the sensor, the fan automatically switches to another

fan setting.

Default sensitivity setting:

Lowest sensitivity setting:

Highest sensitivity setting:

If the sensor control responds too quickly or too slowly, it can

be changed accordingly:

When the fan is switched off, press the

for approx. 4 seconds. The setting is displayed.

The setting of the sensor control is changed by pressing the

+ or – button.

To confirm the entries, press and hold the

approx. 4 seconds.

Lighting

The lighting can be switched on and off independently of the

fan.

Press the

button.

Setting the brightness

Press and hold the

button until the desired brightness is

reached.

Saturation display

When the metal mesh grease filters or the activated carbon

filter are saturated, a signal sounds for approx. 4 seconds after

the fan is switched off.

In addition, the corresponding symbol appears in the display:

Metal mesh grease filter:

■

Activated carbon filter:

■

If you have not yet done so, the metal mesh grease filters

should be cleaned or the activated carbon filter changed now.

For instructions on how to clean the metal mesh grease filters,

please refer to the section Cleaning and maintenance.

While the saturation displays are flashing, they can be reset. To

do this, press the – button.

Switching over the display for circulating-air mode

For circulating-air mode, the electronic control display must be

switched over accordingly:

The extractor hood must be connected and switched off.

■

Press the

and

buttons at the same time until the

■

display for starter sets for circulating-air mode or

™"

display for CleanAir circulating air modules

lights up.

Repeatedly press the button combination to switch the

■

electronic control display back to exhaust air mode (

display).

Audible signal

Switching on the acoustic signal

When the fan is switched off, press the

time for approx. three seconds. An acknowledgement signal

sounds.

Switching off the acoustic signal

Repeat the "Switching on the acoustic signal" process.

†

‹

button and hold it

button for

and + at the same