Siemens IQ500 Manual de instruções de instalação e utilização - Página 7
Procurar online ou descarregar pdf Manual de instruções de instalação e utilização para Máquina de lavar roupa Siemens IQ500. Siemens IQ500 16 páginas.
Também para Siemens IQ500: Manual do utilizador (27 páginas), Manual de instruções de instalação (20 páginas), Manual de instruções de instalação (19 páginas)
Imprimir página
Control panel model 3
Control panel
Explanation
Fan on/off
#
Light on/off/dimming
A
-
Reduce the fan settings
+
Increase the fan settings/intensive setting 1, 2
Boost function (short-term maximum power)
&
Automatic mode with fan run-on time
!
Setting the fan
Switching on the appliance
Press the
button.
#
■
The fan starts at setting
Press the + or - button to change the fan strength.
■
Switching off
Press the
#
button.
Intensive setting
You can use the intensive setting if there is a large build-up of
odours and fumes/vapours.
Press the + button when the fan is at setting
The intensive setting
is activated. Pressing the + button
2‚
again activates the intensive setting
After approx. six minutes, the electronics automatically reduce
the fan to a lower setting . If you want to end the intensive
setting before the preset time expires, press the - button until
the required fan setting is reached.
Boost function
The boost function is a short-term maximum power setting
which can be activated in any fan setting.
Press the
button. After approx. 20 seconds, the fan switches
&
back to the previously set fan setting.
Automatic mode
Switching on the appliance
Press the
#
button.
■
The fan starts at
setting.
ƒ
Press the
!
button.
■
The optimum fan setting
sensor.
Switching off the appliance
Press the
or
button to switch off automatic mode.
!
#
The fan switches off automatically if the sensor no longer
detects a change in the air quality of the room.
The automatic mode lasts 4 hours at most.
ƒ
.
.
„
.
2 ƒ
,
or
is automatically set via a
‚
ƒ
„
Sensor control
In automatic mode, a sensor in the extractor hood detects the
intensity of the cooking and roasting fumes. Depending on the
setting of the sensor, the fan automatically switches to another
fan setting.
Default sensitivity setting:
Lowest sensitivity setting:
Highest sensitivity setting:
If the sensor control responds too quickly or too slowly, it can
be changed accordingly:
When the fan is switched off, press the
1.
for approx. 4 seconds. The setting is displayed.
The setting of the sensor control is changed by pressing the
2.
+ or – button.
To confirm the entries, press and hold the
3.
approx. 4 seconds.
Lighting
The lighting can be switched on and off independently of the
fan.
Press the
button.
A
Setting the brightness
Press and hold the
button until the desired brightness is
A
reached.
Saturation display
When the metal mesh grease filters or the activated carbon
filter are saturated, a signal sounds for approx. 4 seconds after
the fan is switched off.
In addition, the corresponding symbol appears in the display:
Metal mesh grease filter:
■
Activated carbon filter:
■
If you have not yet done so, the metal mesh grease filters
should be cleaned or the activated carbon filter changed now.
For instructions on how to clean the metal mesh grease filters,
please refer to the section Cleaning and maintenance.
While the saturation displays are flashing, they can be reset. To
do this, press the – button.
Switching over the display for circulating-air mode
For circulating-air mode, the electronic control display must be
switched over accordingly:
The extractor hood must be connected and switched off.
■
Press the
and
buttons at the same time until the
#
!
■
display for starter sets for circulating-air mode or
™"
'"
display for CleanAir circulating air modules
lights up.
Repeatedly press the button combination to switch the
■
electronic control display back to exhaust air mode (
display).
Audible signal
Switching on the acoustic signal
When the fan is switched off, press the
time for approx. three seconds. An acknowledgement signal
sounds.
Switching off the acoustic signal
Repeat the "Switching on the acoustic signal" process.
†
‹
Š
button and hold it
!
button for
!
!
"
#
and + at the same
!
7