- ページ 3
ウェザーステーション ACU-RITE 00595のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ACU-RITE 00595 10 ページ。 Professional wireless weather station with wind sensor & atomic clock
ページを印刷する
MOUNTING THE WIRELESS WIND
SPEED AND WIND DIRECTION
SENSOR:
Before permanently mounting the wind
speed bracket, make sure that the
wind-fan and wind-vane can rotate freely
without any disruption. Also note that
the wind speed sensor bracket arm
must be pointing north. The wind speed
sensor should be positioned to allow the
wind to flow around the sensor
unhindered from all directions for the
most accurate and correct readings.
OPTIONAL POLE MOUNTING:
Both sensors are designed to mount in
two ways, either to flat surfaces like wood
posts, or to 3/4" schedule 40 PVC pipe
(the outside dimension of the pipe
actually measures approximately 1, 1/16").
The pipe mounting method is often
referred to in these instructions.
The ideal mounting scenario would be for
the wireless thermo-hygrometer to be
mounted on the north side of the building
and for the wind sensor to be mounted
well away from the building and high in the
air. Please test the wireless signal range
before permanently mounting.
Since PVC pipe is somewhat flexible, if a
tall wind sensor mast is being erected, a
larger diameter PVC pipe should be used
for the base with a reducer fitting placed
at the top.
Plastic pipes used for mounting are
non-conductive and reduce the likelihood
of lightening strikes.
BATTERIES
(not included)
NOTE: Do not install batteries in any of the units until you have read through the initial
set-up steps in their entirety.
BATTERY TYPE:
INDOOR UNIT: "AA" (3) alkaline type batteries can be used for the indoor unit.
WIRELESS OUTDOOR UNITS: It is recommended that LITHIUM type "AA" batteries be used
in any outdoor units when the temperature drops below -4ºF. Alkaline batteries may freeze
at very low temperatures and will fail to provide adequate power to the wireless units.
MAIN UNIT BATTERY REPLACEMENT:
When the low battery indicator icon becomes present, it is recommended that you change
the batteries. Replace only with the same or equivalent type of fresh alkaline batteries.
BATTERY INSTALLATION:
For the first installation, insert the batteries into the two WIRELESS SENSORS FIRST and
then into the main unit.
Thermo-Hygrometer Sensor: (See illustration next page) Rotate and pull the top casing
from the bottom cone by turning the unit upside down and rotating counter-clock wise
until casing pulls apart. Insert 2 fresh "AA" batteries (batteries not included). Replace
the battery compartment cover and rotate the top back into the bottom piece.
Wind Sensor: (See illustration next page) Twist off the top from the bottom and open the
battery cover located on the bottom of the sensor. Insert 2 fresh "AA" batteries.
(Batteries not included). Replace battery door cover by putting battery cover on half way
and then sliding into place. Twist on the top to the bottom piece.
Main Unit: Open the battery cover located on the back of the unit and insert 3 fresh "AA"
batteries. (Batteries not included). Replace battery door cover.
NOTE: When reinstalling the batteries while holding down the "CLEAR" button, all user
settings will be cleared and the unit will set back to the factory default settings. If no
button is pushed during battery replacement, the last record and user settings will be
saved.
NOTE: When installing batteries, always install according to the polarity indicated in the
battery compartment ( + to + and - to - ).
LOW BATTERY INDICATOR:
Low Battery
Low battery indicator is displayed on the main unit for the main unit and all wireless
sensors. When replacing the batteries, please follow the battery installation procedure as
mentioned in this instruction manual. When installing or replacing batteries do not mix
battery types or old batteries with new batteries.
BATTERY REPLACEMENT:
When the low battery indicator icon becomes present, it is recommended that you change
the batteries. Replace only with the same or equivalent type of fresh alkaline batteries. This
method of battery replacement ensures there will be no loss in MIN/MAX and history data.
However, if main unit or sensors have remained without batteries for an extended period of
time, the main unit will lose the MIN/MAX and all weather data recordings and will have to be
synchronized again.
Battery O.K.