携帯電話 Digitalk SP808のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Digitalk SP808 4 ページ。 Digitalk communicator
ページを印刷するOWNER'S MANUAL AND OPERATING INSTRUCTIONS
18
17
16
15
14
13
12
11
10
Communicator Controls
1. Antenna
2. LCD Screen: Displays current channel selection and other radio status
symbols.
3. Monitor M button: Press to tune in and hold onto weak signals.
4. Scan S button: Used to activate/deactivate CHANNEL SCAN.
5. Enter/Back Light
button: Used to turn LCD Screen LAMP ON/OFF.
Buttons are locked when pressed and held.
6. Up
button (VOLUME/CHANNEL): Press to adjust volume level and
change channels.
7. Speaker
8. Battery Compartment (LOCATED ON THE REAR): Houses 3 x 1.5V "AAA"
alkaline batteries or 3.6V "AAA" Ni-MH rechargeable battery pack
(not included).
9. Battery Compartment Cover Latch (LOCATED ON THE REAR): Secures
Battery Compartment cover.
10. Down
button (VOLUME/CHANNEL): Press to adjust volume level and
change channels.
11. Mic: Microphone.
12. Menu
button: Allows you to change channels.
13. Call C button: Press to transmit CALL TONES.
14. PUSH TO TALK PTT button: Press to transmit.
15. TX (Transmission)/RX (Receiving) LED indicator: Illuminates red when
transmitting and green when receiving.
16. Power On/Off
button: Press and hold the button to turn your unit
ON/OFF. Press once to perform Repeater function.
17. External Sp./Mic./Charger Jack: Use for direct recharging with the
car cigarette lighter charger (option).
18. Belt Clip (LOCATED ON THE REAR)
Getting Started
Carefully remove your communicator from its Packing. If there is any
visible damage, do not attempt to operate this communicator. Return
it to the place of purchase.
Figure 1.
Figure 2.
COMMUNICATOR MODEL SP808
Removing the Belt Clip:
1. Pull the BELT CLIP LATCH away from the
unit.
2. While pulling the BELT CLIP LATCH, push
up on the BELT CLIP to remove it from
the unit. See Figure 1.
Installing the Belt Clip:
1. Slide the BELT CLIP into the BELT CLIP
SLOT. See Figure 2.
2. A "click" indicates the BELT CLIP is locked
into position.
Battery Installation:
1
2
3
4
Figure 3.
The COMMUNICATOR has a built in POWER SAVER feature for
5
maximum battery life. But when the COMMUNICATOR is not being
used, conserve battery power by pressing the
6
Remove the batteries if the unit will not be used for a long period
of time.
7
LCD Screen:
8
Baby Monitor
TX Icon
9
Main Channel
Number
RX Icon
Dual Watch
REP Icon
Battery level
Indicator
NOTE: SQ icon only briefly display on LCD screen once turn ON the unit
in SELF-TEST mode.
1. Release the BATTERY COMPARTMENT
COVER LATCH located on the rear side
of the unit (see Figure 3) and remove
the BATTERY COMPARTMENT COVER from
the BATTERY COMPARTMENT (See Figure
4).
2. Install 3x1.5V AAA alkaline batteries or
3.6V "AAA" Ni-MH rechargeable battery
pack (not included) as shown.
3. Reinstall the BATTERY COMPARTMENT
C OV E R a n d l o c k t h e B AT T E R Y
COMPARTMENT COVER LATCH into
Figure 4.
position.
Sub Channel Number
Parent Monitor
Auto Power Off
Channel Scan Selection
TX icon, light on in Transmission mode
Antenna icon, light on in Receiving mode
Rx icon, Light on in Receiving mode
Dual Watch icon, Displayed during Dual Watch mode.
Battery level indicators. Displays current Battery level.
Baby icon, light on in Babysitter unit selection menu
and Standby mode when the System is set to become
a Babysitter unit.
Monitor icon, light on in Parent-monitor unit selection
menu and Standby mode when the System is set to
become a Parent-monitor unit.
Main Channels
, Channel number changes from 1 to 40
as selected by user.
SCAN icon, light on in Channel scanning mode.
Stop watch icon, light on in stop watch mode.
CTCSS code. Sub Channel Number changes from 1 to
38 selected by user.
Music icon, Light on in Call Tone Melody selection menu.
Key lock icon, light on when buttons are locked.
Auto-Power-Off icon, light on in APO selection menu
and Standby mode when APO timer is enabled.
VOX icon, light on in VOX selection menu and Standby
mode when VOX function is enabled.
Numerical digits
Scrambler icon, light on in Scrambler selection menu
and Standby mode when the Scrambler function is
enabled.
REP icon, displays Repeater function.
button to OFF.
Stop Watch
Scrambler
Antenna icon
Call Tone
Melody
VOX icon
Key Lock
Numerical
digits