Digitalk SP808 소유자 매뉴얼

{카테고리_이름} Digitalk SP808에 대한 소유자 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Digitalk SP808 4 페이지. Digitalk communicator

페이지 인쇄

OWNER'S MANUAL AND OPERATING INSTRUCTIONS

Communicator Controls

1. Antenna

2. LCD Screen: Displays current channel selection and other radio status

symbols.

3. Monitor M button: Press to tune in and hold onto weak signals.

4. Scan S button: Used to activate/deactivate CHANNEL SCAN.

5. Enter/Back Light

button: Used to turn LCD Screen LAMP ON/OFF.

Buttons are locked when pressed and held.

6. Up

button (VOLUME/CHANNEL): Press to adjust volume level and

change channels.

7. Speaker

8. Battery Compartment (LOCATED ON THE REAR): Houses 3 x 1.5V "AAA"

alkaline batteries or 3.6V "AAA" Ni-MH rechargeable battery pack

(not included).

9. Battery Compartment Cover Latch (LOCATED ON THE REAR): Secures

Battery Compartment cover.

10. Down

button (VOLUME/CHANNEL): Press to adjust volume level and

change channels.

11. Mic: Microphone.

12. Menu

button: Allows you to change channels.

13. Call C button: Press to transmit CALL TONES.

14. PUSH TO TALK PTT button: Press to transmit.

15. TX (Transmission)/RX (Receiving) LED indicator: Illuminates red when

transmitting and green when receiving.

16. Power On/Off

button: Press and hold the button to turn your unit

ON/OFF. Press once to perform Repeater function.

17. External Sp./Mic./Charger Jack: Use for direct recharging with the

car cigarette lighter charger (option).

18. Belt Clip (LOCATED ON THE REAR)

Getting Started

Carefully remove your communicator from its Packing. If there is any

visible damage, do not attempt to operate this communicator. Return

it to the place of purchase.

Figure 1.

Figure 2.

COMMUNICATOR MODEL SP808

Removing the Belt Clip:

1. Pull the BELT CLIP LATCH away from the

unit.

2. While pulling the BELT CLIP LATCH, push

up on the BELT CLIP to remove it from

the unit. See Figure 1.

Installing the Belt Clip:

1. Slide the BELT CLIP into the BELT CLIP

SLOT. See Figure 2.

2. A "click" indicates the BELT CLIP is locked

into position.

Battery Installation:

Figure 3.

The COMMUNICATOR has a built in POWER SAVER feature for

maximum battery life. But when the COMMUNICATOR is not being

used, conserve battery power by pressing the

Remove the batteries if the unit will not be used for a long period

of time.

LCD Screen:

Baby Monitor

TX Icon

Main Channel

Number

RX Icon

Dual Watch

REP Icon

Battery level

Indicator

NOTE: SQ icon only briefly display on LCD screen once turn ON the unit

in SELF-TEST mode.

1. Release the BATTERY COMPARTMENT

COVER LATCH located on the rear side

of the unit (see Figure 3) and remove

the BATTERY COMPARTMENT COVER from

the BATTERY COMPARTMENT (See Figure

4).

2. Install 3x1.5V AAA alkaline batteries or

3.6V "AAA" Ni-MH rechargeable battery

pack (not included) as shown.

3. Reinstall the BATTERY COMPARTMENT

C OV E R a n d l o c k t h e B AT T E R Y

COMPARTMENT COVER LATCH into

Figure 4.

position.

Sub Channel Number

Parent Monitor

Auto Power Off

Channel Scan Selection

TX icon, light on in Transmission mode

Antenna icon, light on in Receiving mode

Rx icon, Light on in Receiving mode

Dual Watch icon, Displayed during Dual Watch mode.

Battery level indicators. Displays current Battery level.

Baby icon, light on in Babysitter unit selection menu

and Standby mode when the System is set to become

a Babysitter unit.

Monitor icon, light on in Parent-monitor unit selection

menu and Standby mode when the System is set to

become a Parent-monitor unit.

Main Channels

, Channel number changes from 1 to 40

as selected by user.

SCAN icon, light on in Channel scanning mode.

Stop watch icon, light on in stop watch mode.

CTCSS code. Sub Channel Number changes from 1 to

38 selected by user.

Music icon, Light on in Call Tone Melody selection menu.

Key lock icon, light on when buttons are locked.

Auto-Power-Off icon, light on in APO selection menu

and Standby mode when APO timer is enabled.

VOX icon, light on in VOX selection menu and Standby

mode when VOX function is enabled.

Numerical digits

Scrambler icon, light on in Scrambler selection menu

and Standby mode when the Scrambler function is

enabled.

REP icon, displays Repeater function.

button to OFF.

Stop Watch

Scrambler

Antenna icon

Call Tone

Melody

VOX icon

Key Lock

Numerical

digits