- ページ 4

エアコン Argo POLIFEMO CLASSのPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Argo POLIFEMO CLASS 6 ページ。 Evaporative air cooler
Argo POLIFEMO CLASS にも：取扱説明書 (11 ページ)

ページを印刷する

The appliance does not need to be installed.

Position the unit on a flat, stable surface and connect the power cord to a suitable power socket (230 V~): you will hear a

sound to indicate that the appliance is in standby and can be switched on using the START/SPEED button. The unit can

be switched off using the OFF button.

This product can be used either as a fan, with 3 modes (Normal, Natural and Sleep) and 3 fan speed options (low,

medium and high), or as a cooler/humidifier: in this case the rear tank should be filled with

not exceeding the maximum level as indicated. When the water in the tank falls below the minimum level (marked on the

tank), the appliance emits a continuous sound for 10" to signal a low water level, then cooling mode is stopped. The unit

automatically shuts down when the tank is removed.

The fan takes in air from the room and passes it through the dust filter and the evaporative panel, which is constantly

humidified thanks to a system which draws water from the tank and sprays it onto the panel. The incoming hot air makes

part of the water contained in the panel evaporate and is therefore cooler when released back into the room, which makes

it feel as though the temperature has dropped.

START/SPEED button

In standby mode, press this button to start the

appliance, which in 3" will reach its lowest fan

speed level (1); the corresponding LED will

light up. The appliance is set by default to run

in "Normal" mode. Press this button again to

change the fan speed.

1 (low)- 2 (medium) - 3 (high)

COOLER/HUMIDIFIER button

(COOLING/HUMIDIFICATION)

Press this button to activate the "Cooler/Humidifier" mode: the LED

lights up. The fan speed will automatically change to low (1). 5

minutes later, the fan mode and fan speed selected before this mode

was activated will be restored: at this point it will be possible to

change the mode and fan speed set previously, using the MODE

and START/SPEED buttons respectively.

MODE button

Press this button once to switch from "Normal" mode, activated by default when the START/SPEED button is pressed, to "Natural" mode

Press the button a second time to move to "Sleep" mode

corresponding LEDs light up accordingly.

In each of the 3 modes, it will then be possible to select the desired speed: High (3), Medium (2) or Low (1).

The "Natural" mode has 3 fan levels (1, 2, 3), each with different periods in which the high, medium and low speeds alternate, in order to

create a very natural type of ventilation.

An example of this is illustrated on the graph below.

Level 3 (high)

stop

Level 2 (medium)

stop

Level 1 (low)

stop

The "Sleep" mode has 3 fan levels (1, 2, 3), each with different periods in which the high, medium and low speeds alternate in Natural

mode, in order to create a very natural type of ventilation at night.

Sleep mode - Level 3 (high) : 30' in Natural mode level 3 + 30' in Natural mode level 2; then continues in Natural mode level 1.

Sleep mode - Level 2 (medium) : 30' in Natural mode level 2, then continues in Natural mode level 1.

Sleep mode - Level 1 (low) : Natural mode level 1 only.

V 01/12

HOW TO USE THE APPLIANCE

CONTROL PANEL and AVAILABLE FUNCTIONS

FAN MODE SELECTION (Natural, Sleep)

10S

TIMER button

Press this button to start the operating timer for a period

of time between 0.5 and 7.5 hours: every time the button

is pressed, the time will increase by half an hour. It is

deactivated by continuing to press it until the time

disappears.

OFF button

Press this button to exit all

functions and enter standby

mode.

. Press a third time to exit the fan mode selection procedure: the

10S

demineralized

SWING button

(ROTATION)

Press this button to activate

rotation of the round air delivery

grille. Press this button again to

stop rotation. The corresponding

LED lights up and switches off

accordingly.

T=76S

10S

T=74S

minutes

T=74S

water, up to but