- ページ 35
ネットワーク・ハードウェア Cisco ASR 9000 SeriesのPDF マニュアルをオンラインで閲覧またはダウンロードできます。Cisco ASR 9000 Series 44 ページ。 Line card
Cisco ASR 9000 Series にも： ネットワーク設定の構成 (26 ページ), 設定マニュアル (46 ページ), 設定マニュアル (50 ページ), マニュアル (24 ページ), 設定 (46 ページ), クイック・リファレンス・マニュアル (7 ページ)
ページを印刷する
- 1. Field Replaceable Units
- 2. Online Insertion and Removal
- 3. Powering off the Router
- 4. Replacing the Chassis Air Filter
- 5. Required Tools and Equipment
- 6. Removing a Fan Tray
- 7. Installing a Fan Tray
- 8. Disconnecting AC Power
- 9. Reconnecting AC Power
- 10. Disconnecting DC Power
- 11. Reconnecting DC Power
Replacing Cisco ASR 9000 Series Router Components
Backup node in 0/RSP0/CPU0 is NSR-ready
Group
---------
dsc
dlrsc
central-services
v4- routing
netmgmt
mcast-routing
v6-routing
Step 8
From the active RSP, verify that both RSPs have synchronized the SNMP engine ID and SNMP ifindex-table
between each other:
Example:
#more disk0:snmp/ifindex-table loc 0/rsp0/cpu0
#more disk0:snmp/ifindex-table loc 0/rsp1/cpu0
#more disk0:snmp/snmp_persist loc 0/rsp0/cpu0
#more disk0:snmp/snmp_persist loc 0/rsp1/cpu0
Step 9
Manually copy Embedded Event Manager (EEM) scripts from RSP440 to RSP880 disks if applicable.
Note
Step 10
Perform redundancy switchover from active RSP440 (slot 1) to standby RSP880 in (slot 0)
Example:
Router# redundancy switchover
Step 11
Remove RSP440 from slot 1. Follow the procedure explained in the topic
from the Chassis, on page
Step 12
Insert and boot RSP880. After booting, the RSP 880 becomes standby RSP. Do not set the ROMMON variable.
Step 13
Repeat Step 7, Step 8 and Step 9.
Step 14
(Optional) Perform FPD upgrade on the RSP880. Use these commands:
Example:
Router# (admin) upgrade hw-module fpd all location 0/rsp0/cpu0
Router# (admin) upgrade hw-module fpd all location 0/rsp1/cpu0
Step 15
Clear ROMMON variable for active RSP from XR prompt:
Example:
Router# run nvram_rommonvar RSP_LINK_1G 0
Primary
Backup
---------
---------
0/RSP1/CPU0
0/RSP0/CPU0
0/RSP1/CPU0
0/RSP0/CPU0
0/RSP1/CPU0
0/RSP0/CPU0
0/RSP1/CPU0
0/RSP0/CPU0
0/RSP1/CPU0
0/RSP0/CPU0
0/RSP1/CPU0
0/RSP0/CPU0
0/RSP1/CPU0
0/RSP0/CPU0
The EEM scripts are files located on RSP's hard disk. These files are not automatically synced
between Active and Standby RSPs.
25.
Migrating from RSP440 to RSP880 or RSP880-LT Card
Status
---------
Ready
Ready
Ready
Ready
Ready
Ready
Removing and Replacing Cards
Replacing Cisco ASR 9000 Series Router Components
35