- ページ 18

ソフトウェア Epson PowerLite 8300i with EasyMP.net moduleのPDF クイックマニュアルをオンラインで閲覧またはダウンロードできます。Epson PowerLite 8300i with EasyMP.net module 20 ページ。 Release of check tool for network projectors v1.00 for windows
Epson PowerLite 8300i with EasyMP.net module にも：ユーザーマニュアル (42 ページ), 操作マニュアル (36 ページ), 操作マニュアル (47 ページ), クイックセットアップ (2 ページ), 製品サポート速報 (27 ページ), パーツリスト (1 ページ), 補足マニュアル (2 ページ), パンフレット＆スペック (2 ページ), ユーザーマニュアル (1 ページ), 製品サポート速報 (25 ページ), 製品サポート速報 (22 ページ), 製品サポート速報 (28 ページ), 製品サポート速報 (41 ページ), 製品サポート速報 (34 ページ), 製品サポート速報 (28 ページ), 製品サポート速報 (15 ページ), 製品サポート速報 (22 ページ), クイックセットアップ (2 ページ)

ページを印刷する

Epson PowerLite 8300i with
EasyMP.net module クイックマニュアル

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the surface.

Use a canister of compressed air to remove dust.

To remove dirt or smears on the lens, use lens-cleaning

paper. If necessary, moisten a soft cloth with lens cleaner

and gently wipe the lens surface.

Caution: Do not use glass cleaner to clean the lens.

Cleaning the Projector

Before you clean the case, first turn off the projector and

unplug the power cord.

To remove dirt or dust, wipe the case with a soft, dry,

lint-free cloth.

To remove stubborn dirt or stains, moisten a soft cloth with

water and a mild detergent. Then wipe the case.

Do not use wax, alcohol, benzene, paint thinner, or other

chemical detergents. These can damage the case.

Cleaning and Replacing the Air Filters

Clean the air filters on the bottom of the projector after every

100 hours of use. If they are not cleaned periodically, they can

become clogged with dust, preventing proper ventilation. This

can cause overheating and damage the projector.

To clean the air filters, follow these steps:

1. Turn off the projector and unplug the power cord.

2. To clean the filters, EPSON recommends using a small

vacuum cleaner designed for computers and other office

equipment. If you don't have one, gently clean the filters

with a soft brush (such as an artist's paintbrush).

EPSON PowerLite 8300i Projector

3. If the dirt is difficult to remove or a filter is broken, replace

the filters as described below. Contact your dealer or call

EPSON at (800) 873-7766 in the United States to obtain

new ones. In Canada, please call (800) 463-7766 for dealer

referral.

Note: When you replace the lamp, new filters are included

with the lamp. This is a good time to replace them.

Replacing the Filters

1. Turn the projector over (unless it's ceiling-mounted).

2. Remove the filters from the projector by sliding them out

to the sides.

3. Remove each filter from its holder by releasing the two tabs,

as shown.

4. Install new filters in the holders, aligning the tabs with the

slots on each side.

5. Slide the assembled filters back into the projector.

5/03

EPSON PowerLite 8300i Projector

Tabs