- ページ 9
ステレオシステム Philips AZ 2045のPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。Philips AZ 2045 9 ページ。 Cd soundmachine
Philips AZ 2045 にも: ユーザーマニュアル (15 ページ), 仕様 (2 ページ), ユーザーマニュアル (12 ページ), マニュアル (8 ページ), サービスマニュアル (34 ページ), マニュアル (10 ページ), (スウェーデン語)Snabbmanual (8 ページ)
CASSETTE RECORDER
CD Synchro Start recording
1 Select CD function.
2 Insert a CD and if desired, program track numbers.
3 Open the cassette door.
4 Insert a suitable tape into the cassette deck and
close the door.
5 Press RECORD 0 to start recording.
– Playing of the CD program starts automatically
from the beginning of the program. You don't
need to start the CD player separately.
™ To select and record a particular passage within
a CD track:
• Press ∞ or §. Release the control when you
recognize the passage you want.
• To pause CD playback, press 2;.
• Recording starts from this exact point in the
track when you press RECORD 0.
6 To pause recording, press PAUSE ;.
Press PAUSE ; again to resume recording.
7 To stop recording, press STOP 9.
Recording from the Radio
1 Tune to the desired radio station (see Tuning to
radio stations).
2 Follow steps 3-7, under Synchro Start CD
recording.
MAINTENANCE & SAFETY
Maintenance & Safety
CD player and CD handling (See 6)
• If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set
to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature
can cause condensation on the lens of your CD
player. Playing a CD is then not possible. Do not
attempt to clean the lens but leave the set in a
warm environment until the moisture evaporates.
• Always close the CD door to avoid dust on the
lens.
• To clean the CD, wipe in a straight line from the
center towards the edge using a soft, lint-free
cloth. Do not use cleaning agents as they may
damage the disc.
• Never write on a CD or attach any stickers to it.
Safety Information
• Don't expose the set, batteries, CDs or cassettes to
humidity, rain, sand or excessive heat.
• Clean the set with a dry cloth. Don't use any
cleaning agents containing alcohol, ammonia,
benzene or abrasives as these may harm the set.
• Place the set on a hard and flat surface so that the
system does not tilt. Make sure there is good
ventilation to prevent the set overheating.
• The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
Tape deck maintenance (See 7)
To ensure quality recording and playback of the tape
deck, clean parts A, B and C as shown, once a
month. Use a cotton bud slightly moistened with
alcohol or a special head cleaning fluid to clean the
deck.
1 Open the cassette door.
2 Press PLAY 2 and clean the roller C.
3 Press PAUSE ; and clean the heads A, and the
capstan B.
4 After cleaning, press STOP 9.
TROUBLESHOOTING
WARNING
Do not open the set as there is a risk of electric shock! Under no circumstances should you try to
repair the set yourself, as this will invalidate the warranty.
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.
Remote control does not function properly/
cannot turn on the set
– Set is switched off
• Press y button on the set to switch on (See note:
remote control)
– Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– Headphones connected to the set
• Disconnect headphones
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Increase the distance
Poor radio reception
– Weak radio signal
• FM: Adjust the FM telescopic aerial
Environmental information
We have done our best to reduce the packaging and make it easy to separate into 3 materials: cardboard,
expandable polystyrene, polyethylene.
Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe
the local regulations regarding the disposal of packaging, dead batteries and old equipment.
Poor cassette sound quality
– Dust and dirt on the heads, etc.
• Clean deck parts, see Maintenance
– Use of incompatible cassette types
(METAL or CHROME)
• Only use NORMAL (IEC I) for recording
Recording does not work
– Cassette tab(s) may be broken
• Apply adhesive tape over the missing tab space
indication
– CD badly scratched or dirty
• Replace/ clean CD, see Maintenance
– Laser lens steamed up
• Wait until lens has cleared
indication
– CD-R(W) is blank/ not finalized
• Use a finalized CD-R(W)
indication
– CD-ROM disc inserted/
CD contains non-audio files
• Use CD Audio discs only/
press ∞ or § once or more to skip to a CD audio
track instead of the data files
The CD skips tracks
– CD damaged or dirty
• Replace or clean CD
– SHUFFLE or PROGRAM is active
• Switch off SHUFFLE / PROGRAM