- ページ 7

アンプ Pioneer A-757のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Pioneer A-757 13 ページ。
Pioneer A-757 にも：取扱説明書 (14 ページ)

ページを印刷する

PANEL FACILITIES

(ADPT/TAPE 3 switch in the A-656)

Use this switch to listen to tape playback, or to listen to the

sounds being recorded during tape recording.

ON:

The indicator lights: Press when listening to the playback sound of

the tape deck or the adaptor connected

to the ADPT 1/TAPE 3

IN/PLAY terminals, or to monitor the sound being recorded on the

tape deck connected to the ADPT 1/TAPE 3 OUT/REC terminals.

OFF:

The indicator goes off: Normally leave the switch in this position.

NOTE:

When the DIRECT switch is set to ON, this function does not

operate and no signal is output at the ADPT 1/TAPE 3 OUT/REC

terminals.

@ DIRECT switch/indicator

Use this switch when you do not wish to pass the output from input

terminal

equipment

through

the

various

frequency

adjusting

circuits and adaptor terminals (ADPT 1/TAPE 3, ADPT 2, BASS,

TREBLE, BALANCE, LOUDNESS).

ON:

When the switch is in this position, the indicator lights and the

signals input from the input terminals

are reproduced without

passing

through

the various frequency-adjusting circuits. This

results in flat, pure sound which is a more faithful reproduction of

the input source.

OFF:

When the switch is in this position the indicator goes out and the

signal passes through the various frequency adjusting circuits.

@ PHONO SELECTOR switch

Set in accordance with the type of cartridge used in you turntable.

MM:

Set to this position when using a moving magnet cartridge, or a

MC (moving coil) cartridge with high output of 1 mV or more.

MC:

Set to this position when using a moving coil cartridge.

MM SUBSONIC/MC SUBSONIC:

Subsonic filter for moving coil or moving magnet cartridges to cut

ultralow frequency noise less than 17 Hz generated when playing

a warped record.

When using a high-output moving coil cartridge, set this switch to

MM or MM SUBSONIC.

@ VOLUME CONTROL

Use to adjust volume level.

NOTE:

This unit is equipped with a circuit that attenuates the effect of tone

and loudness controls at volume is turned up.

@ MUTING switch/indicator (A-757 only)

Use to temporarily cut sound volume.

ON:

The indicator lights. The sound volume will be cut off.

OFF:

The indicator goes off. The sound will return to its previous volume.

@ INPUT SELECTOR switch

Use to select playback source.

LINE:

Set to this position when

listening to the programs

from

component connected to the LINE terminals.

TUNER:

Set to this position when listening to AM or FM broadcasts with a

tuner,

PHONO:

Set

to this

position

when

listening

to record

playback

turntable.

cD:

Set to this position when listening to a compact disc playback with

aCbD player.

DAT/TAPE 1:

For playback with a tape deck or digital audio tape deck connected

to the DAT/TAPE 1 terminals.

TAPE 2:

For playback with a tape deck connected to the TAPE 2 terminals.

® REC SELECTOR switch

Switch to select recording signal. When set at other than SOURCE

or OFF position, signals can be recorded during playback of the

equipment selected by INPUT SELECTOR switch.

TUNER:

To record from a TUNER.

cD:

To record from a CD player.

OFF:

In this position nothing from the REC terminals of DAT/TAPE 1 and

TAPE 2 will be output. Select it when not recording; output to tape

decks will be disconnected, improving sound quality.

SOURCE:

To record the equipment selected by INPUT SELECTOR switch.

TAPE:

To record (copy) from the tape deck of DAT/TAPE

1 terminals,

over to the tape deck of TAPE 2 terminals.

To record (copy) from the tape deck of TAPE 2 terminals, over to

the tape deck of DAT/TAPE 1 terminals.

NOTE:

The REC SELECTOR switch has no effect on the recording out put

of the ADPT 1/TAPE 3 terminals.