- ページ 24

プリンター Xerox WORKCENTRE 7120のPDF リファレンス・マニュアルをオンラインで閲覧またはダウンロードできます。Xerox WORKCENTRE 7120 29 ページ。 Color networking mfp a3
Xerox WORKCENTRE 7120 にも： 評価者マニュアル (25 ページ), 評価者マニュアル (24 ページ), リファレンス・マニュアル (30 ページ), 仕様 (14 ページ), 仕様 (14 ページ), 競合他社との比較 (11 ページ), 競合他社との比較 (11 ページ), パンフレット＆スペック (4 ページ), クイック・ユース・マニュアル (20 ページ), クイック・ユース・マニュアル (20 ページ), クイック・ユース・マニュアル (20 ページ), クイック・ユース・マニュアル (20 ページ), インストレーション・マニュアル (2 ページ), インストレーション・マニュアル (2 ページ), クイック・ユース・マニュアル (20 ページ), リファレンス・マニュアル (32 ページ), システム管理者マニュアル (20 ページ)

ページを印刷する
Xerox WORKCENTRE 7120 リファレンス・マニュアル
Figure 11. Model 7120 Input Hopper
3.
Place the card file to be read in the input hopper (face
down, row 9 away from the operator) with the card
weight on top of the card file.
4.
Press the START switch to feed the first card of the file
from the input hopper to the card read platform. Illu-
mination of the START switch indicates that the card
reader is ready for automatic reading of the card fi Ie
by the controlling system.
CARD FILE UNLOADING PROCEDURE (MODEL 7120)
1.
Press the STOP switch to place the card reader in the
"ready manual
ll
state.
Remove the card weight and
the remainder of the card file from the input hopper.
2.
Press the RESET switch to feed the card on the card
read platform into alternate stacker 2.
To maintain
the correct sequence of the card file, this card should
be placed in front of the bottom card taken from the
input hopper.
Figure 12. Model 7120 Multiple Output Stackers
18
Card File Unloading/Loading Procedures
CARD FILE LOADING PROCEDURElMODELS 7121/7122)
I
READER HALTED
1.
Remove the card weight (and any card present) from
input hopper (see Figure 13).
Cards may remain in
the output stacker provided it is not full (indicated by
illumination of the STACKER light).
Press the RESET
switch to initialize the reader and clear fault conditions.
The transport motor may start depending upon the posi-
tion of the POWER switch.
2.
Ensure power is applied by visually checking the
POWER indicator on the operator control panel. Illu-
mination of the POWER indicator and audible mechanical
operation indicate ac and dc power are applied and the
read station and transport mechanism are operative.
3.
Place the card file to be read in the input hopper
(printed side down and column one to the right). Place
the card weight on top of the cards with the circular
hole in the weight to the left and down.
4.
Press the START switch.
Illumination of the START
indicator indicates that the card reader is ready for
automatic reading of the card fi Ie by the controlling
system.
READER RUNNING
1.
With a minimum 2-inch stack of cards remaining in the
input hopper, remove the card weight.
2.
Load additional cards and replace the card weight.
Figure 13. Models 7121/7122 Input Hopper
and Output Stacker