Xerox WORKCENTRE 7120 참조 매뉴얼 - 페이지 24

{카테고리_이름} Xerox WORKCENTRE 7120에 대한 참조 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Xerox WORKCENTRE 7120 29 페이지. Color networking mfp a3
Xerox WORKCENTRE 7120에 대해서도 마찬가지입니다: 평가자 매뉴얼 (25 페이지), 평가자 매뉴얼 (24 페이지), 참조 매뉴얼 (30 페이지), 사양 (14 페이지), 사양 (14 페이지), 경쟁사 비교 (11 페이지), 경쟁사 비교 (11 페이지), 브로셔 및 사양 (4 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 빠른 사용 설명서 (20 페이지), 설치 매뉴얼 (2 페이지), 설치 매뉴얼 (2 페이지), 빠른 사용 설명서 (20 페이지), 참조 매뉴얼 (32 페이지), 시스템 관리자 매뉴얼 (20 페이지)

페이지 인쇄

1. General Description

Figure 11. Model 7120 Input Hopper

Place the card file to be read in the input hopper (face

down, row 9 away from the operator) with the card

weight on top of the card file.

Press the START switch to feed the first card of the file

from the input hopper to the card read platform. Illu-

mination of the START switch indicates that the card

reader is ready for automatic reading of the card fi Ie

by the controlling system.

CARD FILE UNLOADING PROCEDURE (MODEL 7120)

Press the STOP switch to place the card reader in the

"ready manual

state.

Remove the card weight and

the remainder of the card file from the input hopper.

Press the RESET switch to feed the card on the card

read platform into alternate stacker 2.

To maintain

the correct sequence of the card file, this card should

be placed in front of the bottom card taken from the

input hopper.

Figure 12. Model 7120 Multiple Output Stackers

Card File Unloading/Loading Procedures

CARD FILE LOADING PROCEDURElMODELS 7121/7122)

READER HALTED

Remove the card weight (and any card present) from

input hopper (see Figure 13).

Cards may remain in

the output stacker provided it is not full (indicated by

illumination of the STACKER light).

Press the RESET

switch to initialize the reader and clear fault conditions.

The transport motor may start depending upon the posi-

tion of the POWER switch.

Ensure power is applied by visually checking the

POWER indicator on the operator control panel. Illu-

mination of the POWER indicator and audible mechanical

operation indicate ac and dc power are applied and the

read station and transport mechanism are operative.

Place the card file to be read in the input hopper

(printed side down and column one to the right). Place

the card weight on top of the cards with the circular

hole in the weight to the left and down.

Press the START switch.

Illumination of the START

indicator indicates that the card reader is ready for

automatic reading of the card fi Ie by the controlling

system.

READER RUNNING

With a minimum 2-inch stack of cards remaining in the

input hopper, remove the card weight.

Load additional cards and replace the card weight.

Figure 13. Models 7121/7122 Input Hopper

and Output Stacker