- ページ 4

食器洗い機 Zanussi DCS 383のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。Zanussi DCS 383 12 ページ。 Dishwasher dcs 383
Zanussi DCS 383 にも：取扱説明書 (12 ページ)

ページを印刷する

Description of the appliance

Rinse aid dispenser 1

Use of a rinse conditioner will result in cleaner and faster

drying of the load, since it helps water and soil to run off.

Too much conditioner may result in streakiness, too little

may cause white spots. The dispenser holds about 140 ml.

This is enough for 40-70 wash cycles, depending on the

dosage setting. When the rinse conditioner level is approa-

ching the bottom of the scale it is time to reﬁll the dispenser.

Swivel out the ﬁller trough and carefully ﬁll up with rinse

conditioner until the level reaches the red mark on the level

indicator tube. Do not overﬁll and carefully wipe off any

spillage to prevent sudsing problems. Don't forget the close

the ﬁller trough afterwards. Adjust the dosage setting accor-

ding to the hardness of the water. Begin with the lowest

dosage setting and increase as necessary by turning the

arrow clockwise.

Do not ﬁll the rinse aid dispenser with liquid

detergent.

Spray arm 2

It is important to keep all the holes in the spray arm clear.

If the spray arm becomes blocked this will affect washing

efﬁciency. If the spray arm needs cleaning, unscrew the

nut clockwise (left-hand thread) and lift off the spray arm.

Clear the holes and shake out any food particles.

Coarse strainer 3

The purpose of the coarse strainer is to catch large objects,

such as toothpicks and pieces of eggshell. Make sure that

the strainer is always clean. Lift it out and rinse it under

running water whenever necessary.

Fine ﬁlter 4

It is just as important to keep this filter clean. A dirty or

clogged ﬁlter will impair washing efﬁciency. The ﬁne ﬁlter

can easily be lifted out for cleaning when you have removed

the coarse strainer.

Detergent dispenser 5

Only use detergents specially designed for dishwashers.

For a normal load pour about 1-2 tablespoons of detergent

into the detergent dispenser.

Water softener 6

This dishwasher is equipped with a water softener for hard

(chalky) water, therefore the rinse aid dispenser should

be set for a low dosage.

The lime (chalk) in hard water causes white deposits to

occur on dishes and the interior of the dishwasher.

To prevent this, the water has to pass through a special

container where its hardness is removed. Since the water

softener consumes coarse dishwasher salt, you will have

to replenish the salt container after a certain number of

dishwashing cycles. When the indicator lamp on the

control panel lights up, it is time to ﬁll up with salt.

Proceed as follows:

1. Unscrew the salt container ﬁller cap.

2. Fill up salt container with water (only the ﬁrst

time).

3. Fill the container with coarse salt. Use the funnel

supplied with the machine.

Ordinary domestic salt will affect the efﬁency of

the water softener and damage it.

4. Remove the funnel and wipe off any spillage.

5. Screw the ﬁller cap back in place.

The salt container holds about 1 litre, which is enough for

about 20 - 30 dishwashing cycles. Always ensure that

there is water in the salt container before ﬁlling salt.

Water softener plug

As supplied from the factory, the water softener is set for

a water hardness of up to 20° dH. If your water is harder

than this, you can increase the capacity of the water

softener by pulling out the rubber plug at the rear of the

dishwasher on the left hand side viewed from the back.

See illustration.

Contact your local Water Authority to ﬁnd the exact water

hardness level for your area.

Never run the dishwasher without salt in the

container as this may damage the water softener.

- 4 -