電動工具 ARO PG087A-A5のPDF 取扱説明書をオンラインで閲覧またはダウンロードできます。ARO PG087A-A5 16 ページ。 Impulse wrench

ページを印刷する

ARO

OPERATOR'S MANUAL

SECTION

M35

INCLUDING: OPERATION, INSTALLATION & MAlNTENANCE

Released: 8-1-97

Tool Products

IMPULSE WRENCH

MODEL:

PG087A-A5

Model PG087A-A5

impulse

Wrench

is designed

for assembly

operations

which

require

high speed

rundown

of fasteners

with consistent

torque

delivery

and reduced

torque

reaction.

ARO is not responsible

for customer

modification

of tools for applications

on which ARO was not

consulted.

IMPORTANT SAFETY INFORMATION ENCLOSED,

READ THIS MANUAL BEFORE OPERATING TOOL.

IT IS THE RESPONSIBILITY

OF THE EMPLOYER TO PLACE THE INFORMATION

IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.

FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.

PLACING TOOL IN SERVICE

Always operate, inspect and maintain this tool in

accordance with all regulations (local, state,

federal and country), that may apply to hand held/

hand operated pneumatic tools.

For safety, top performance, and maximum

durability

of parts, operate this tool at 90 psig

(6.2 bar/620 kPa) maximum air pressure at the

inlet with 3/8" (10 mm) inside diameter air supply

hose.

Always turn off the air supply and disconnect the

air supply hose before installing,

removing or

adjusting any accessory on this tool, or before

performing

any maintenance on this tool.

Do not use damaged, frayed or deteriorated

air

hoses and fittings.

Be sure all hoses and fittings are the correct size

and are tightly secured. See Dwg. TPD905-1 for a

typical piping arrangement.

Always use clean, dry air at 90 psig

(6.2 bar/620 kPa) maximum air pressure. Dust,

corrosive fumes and/or excessive moisture can ruin

the motor of an air tool.

Do not lubricate tools with flammable or volatile

liquids such as kerosene, diesel or jet fuel.

Do not remove any labels. Replace any damaged

label.

USING THE TOOL

Always wear eye protection when operating or

Always wear hearing protection when operating this-

tool.

Keep bands, loose clothing and long hair away from

rotating end of tool.

Note the position of the reversing lever before

operating the tool so as to be aware of the direction of

rotation when operating the throttle.

Anticipate

and be alert for sudden changes in

motion during start up and operation of any power

tool.

Keep body stance balanced and firm. Do not over-

reach when operating this tool. High reaction

torques can occur at or below the recommended

air pressure.

Tool shaft may continue to rotate briefly after

throttle is released.

Air powered tools can vibrate in use. Vibration,

repetitive motions or uncomfortable

positions may

be harmful to your hands and arms. Stop using any

tool if discomfort, tingling feeling or pain occurs.

Seek medical advice before resuming use.

Use accessories recommended by ARO.

Use only impact sockets and accessories. Do not use

hand (chrome) sockets or accessories.

Impact wrenches are not torque wrenches.

Connections requiring

specific torque must be

checked with a torque meter after fitting with an

impact wrench.

This tool is not designed for working in explosive

atmospheres.

performing maintenance on this tool.

The use of other than genuine ARO replacement parts may result in safety hazards, decreased tool performance, and

increased maintenance, and may invalidate all warranties.

Repairs should be made only by authorized trained personnel.

Consult your nearest ARO Tool Products Authorized

Servicenter.

For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand

Distribution Center,

White House, TN at PH: (615) 672-0321,

FAX:

(615) 672-0601

ARO Tool Products

Ingersoll-Rand

Company

ARO

1725

U.S. No. 1 North, PO Box 8000, Southern Pines, NC 28388-8000

INGERSOLL-RAND

COMPANY

PRINTED IN U.S.A.

Part of worldwide

Ingersoll-Rand