ARO PG087A-A5 Operator's Manual

Browse online or download pdf Operator's Manual for Power Tool ARO PG087A-A5. ARO PG087A-A5 16 pages. Impulse wrench

ARO
OPERATOR'S MANUAL
SECTION
M35
89
INCLUDING: OPERATION, INSTALLATION & MAlNTENANCE
Released: 8-1-97
Tool Products
IMPULSE WRENCH
MODEL:
PG087A-A5
Model PG087A-A5
impulse
Wrench
is designed
for assembly
operations
which
require
high speed
rundown
of fasteners
with consistent
torque
delivery
and reduced
torque
reaction.
ARO is not responsible
for customer
modification
of tools for applications
on which ARO was not
consulted.
IMPORTANT SAFETY INFORMATION ENCLOSED,
READ THIS MANUAL BEFORE OPERATING TOOL.
IT IS THE RESPONSIBILITY
OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
l
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state,
federal and country), that may apply to hand held/
hand operated pneumatic tools.
l
For safety, top performance, and maximum
durability
of parts, operate this tool at 90 psig
(6.2 bar/620 kPa) maximum air pressure at the
inlet with 3/8" (10 mm) inside diameter air supply
hose.
l
Always turn off the air supply and disconnect the
air supply hose before installing,
removing or
adjusting any accessory on this tool, or before
performing
any maintenance on this tool.
.
Do not use damaged, frayed or deteriorated
air
hoses and fittings.
.
Be sure all hoses and fittings are the correct size
and are tightly secured. See Dwg. TPD905-1 for a
typical piping arrangement.
l
Always use clean, dry air at 90 psig
(6.2 bar/620 kPa) maximum air pressure. Dust,
corrosive fumes and/or excessive moisture can ruin
the motor of an air tool.
l
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
l
Do not remove any labels. Replace any damaged
label.
USING THE TOOL
l
Always wear eye protection when operating or
.
.
.
.
.
.
.
.
.
.
.
Always wear hearing protection when operating this-
tool.
Keep bands, loose clothing and long hair away from
rotating end of tool.
Note the position of the reversing lever before
operating the tool so as to be aware of the direction of
rotation when operating the throttle.
Anticipate
and be alert for sudden changes in
motion during start up and operation of any power
tool.
Keep body stance balanced and firm. Do not over-
reach when operating this tool. High reaction
torques can occur at or below the recommended
air pressure.
Tool shaft may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable
positions may
be harmful to your hands and arms. Stop using any
tool if discomfort, tingling feeling or pain occurs.
Seek medical advice before resuming use.
Use accessories recommended by ARO.
Use only impact sockets and accessories. Do not use
hand (chrome) sockets or accessories.
Impact wrenches are not torque wrenches.
Connections requiring
specific torque must be
checked with a torque meter after fitting with an
impact wrench.
This tool is not designed for working in explosive
atmospheres.
performing maintenance on this tool.
The use of other than genuine ARO replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel.
Consult your nearest ARO Tool Products Authorized
Servicenter.
For parts and service information, contact your local ARO distributor, or the Customer Service Dept. of the Ingersoll-Rand
Distribution Center,
White House, TN at PH: (615) 672-0321,
FAX:
(615) 672-0601
ARO Tool Products
Ingersoll-Rand
Company
ARO
1725
U.S. No. 1 North, PO Box 8000, Southern Pines, NC 28388-8000
©1997
INGERSOLL-RAND
COMPANY
PRINTED IN U.S.A.
Part of worldwide
Ingersoll-Rand