- ページ 7

スピーカーシステム Acoustic Energy AEGO 5のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Acoustic Energy AEGO 5 8 ページ。 Powered 5.1 surround sound speaker system

AEGOp5 Operation
AEGOp5 Operation

- Delay Calibration

Centre
Subwoofer
Front
Front
Right
Left
Rear Left
Rear Right
The recommended listening position is described below:
Centre channel speaker should be placed the same distance as the
left and right speakers from your listening position.
Rear left and right speakers should be placed behind your listening
position and above ear level.
If speaker placement is restricted due to the physical environment
of the room, delay calibration is sometimes necessary to achieve
the ideal listening environment.
If the centre speaker can only be placed nearer to you than the left
and right speakers, sound from the centre speaker will arrive
before the sound from the left and right speakers. The difference in
arrival time could may affect the sound quality and effect. Your
AEGO
5 allows you to adjust the speaker time delay to compensate
P
for this problem by increasing the delay time for the centre channel.
Thus sound from the centre, left and right speakers will reach you
at the same time. If your centre speaker is closer to your listening
position than the left and right speakers, press DELAY button
repeatedly until the centre channel is selected. To increase or
decrease the delay time, press D TIME + or D TIME - until the
desired delay is selected. The same procedure can be applied to
adjust the delay time of rear surround speakers if necessary.
AEGOp5 Operation - Time Delay
Adjustment on Centre Channel
Speaker
Delay Calibration
mute
test
Press the DELAY button and repeat to
balance
delay
prologic
select the length of delay time for the
field
EQ on/off
EQ setup
Rear Left (SL), Rear Right (SR) and
Centre(C) channels.
preset 1
preset 2
preset 3
save1
preset 4
load
The delay range for SL/SR is 0 to 15
BassManager
Cen
ms and 0 to 5 ms for centre.
SL/SR
SW
VOL
D Time
Adjust the delay time for the selected
DRC
channel by pressing D TIME + or D
reset
TIME - on the remote control.
Press the DELAY Button will display the current
delay time for channel LS.
DOLBY DIGITAL CO
DELAY
SL 5 MS
Press the DELAY Button again will circle to next channel.
DOLBY DIGITAL CO
DELAY
SR 5 MS
Press the D TIME + or D TIME - button will increase or
decrease the delay time for current channel.
DOLBY DIGITAL CO
DELAY
SR 6 MS
AEGOp5 Operation - Time Delay
Adjustment on Surround
Speakers
Delay Calibration
mute
Press DELAY Button and repeat to
balance
delay
select the length of delay time for
field
EQ on/off
SL/SR/C channels.
preset 1
preset 2
The delay range for SL/SR is 0 to 15 ms
save1
preset 4
and 0 to 5 ms for centre.
BassManager
Adjust the delay time on selected
SL/SR
channel by pressing D TIME + or
DRC
D TIME - on the remote control.
reset
Surround Speaker Delay
Delay calibration for the rear surround
speakers may be necessary if the surround speakers are placed quite
close to your listening position. To correct the delay this may cause,
press the DELAY button repeatedly until SL or SR appear on the
display. Increase the time delay of the surround speakers by pressing
D TIME + until you are able to hear a 3D sound effect coming from
surround speakers.
Press DELAY Button again to move to the next channel.
DOLBY DIGITAL CO
DELAY
SL 5 MS
DOLBY DIGITAL CO
DELAY
SR 5 MS
Press D TIME + or D TIME - to increase or decrease
the delay time for the selected channel.
DOLBY DIGITAL CO
DELAY
SR 6 MS
12
AEGOp5 Operation

- Pro Logic Mode

Pro Logic Mode
Your AEGO
5 will automatically switch to
P
Pro Logic mode when it detects a Pro Logic
signal. With other types of input signal, you
can select the Dolby Pro Logic mode
manually by pressing Pro Logic button on
the remote. Repeatedly pressing the
Pro Logic Button will switch the Pro Logic
mode in between the following modes;
AUTO, ALL PCM, ENABLE and DISABLE.
If a Pro Logic signal is detected, AEGO
mode automatically, and the display shows the following information:
DOLBY DIGITAL CO
PROLOGIC AUTO
test
If a stereo signal (either analog or digital) is detected, AEGO
prologic
switch to stereo mode automatically. You can then convert the stereo
mode to Pro Logic mode by pressing the Prologic button until you see
EQ setup
the following on the display:
preset 3
DOLBY DIGITAL CO
load
PROLOGIC ALL PCM
Cen
DOLBY DIGITAL CO
SW
PROLOGIC ENABLE
VOL
D Time
If you want to convert Pro Logic or 2-channel Dolby Digital signal into
Stereo mode, you can press the Prologic button until you see the
following on the display:
DOLBY DIGITAL CO
PROLOGIC DISABLE
AEGOp5 Operation - Speaker
Mode with Bass Manager

Speaker Mode with Bass Manager

The six LEDs on front panel of your AEGO
represent the six discrete audio channels
(Left, Right, Centre, Rear Left, Rear Right
and Sub). If a particular channel is active,
the LED will light up in green. The LED will
be red if that particular channel carries
bass signal below 120Hz.
Speaker Mode
Pressing the CEN button, switches the
centre channel on and off. The LCD will
display the following:
DOLBY DIGITAL CO
SPK C
ON
DOLBY DIGITAL CO
SPK C
OFF
AEGOp5 Operation
Pressing the SL or SR button, switches the surround
channels on and off. The LCD will display the following:
DOLBY DIGITAL CO
SPK SUR
input
power
DOLBY DIGITAL CO
SPK SUR
mute
test
balance
delay
prologic
Pressing the SW button, switches the subwoofer on and off.
field
EQ on/off
EQ setup
The LCD will display the following:
preset 1
preset 2
preset 3
DOLBY DIGITAL CO
save1
preset 4
load
SPK SW
BassManager
Cen
DOLBY DIGITAL CO
SL/SR
SW
SPK SW
OFF
VOL
D Ti
Bass Manager
5 will switch to Pro Logic
P
Pressing the BASS MANAGER button enables you to select from
three different settings of Bass; Bass Config.1, Bass Config.2 and
Bass Config.3. These selections will feed the bass signal
below 120Hz to different speakers as described below.
5 will
P
Bass Config.1
With this setting, the bass signal below 120Hz will be sent to the
subwoofer; the LEDs on the front panel indicating SW will be red,
and the LCD will show the following:
DOLBY DIGITAL CO
BASS CONFIG.1
Bass Config.2
With this setting, the bass signal below 120Hz will be sent to front left
and right speakers and the subwoofer; the LEDs on the front panel
indicating L/R/SW will be red, and the LCD will show the following
information:
DOLBY DIGITAL CO
BASS CONFIG.2
Bass Config.3
With this setting, the bass signal below 120Hz will be sent to all the
speakers; the LEDs on the front panel indicating L/R/SL/SR/SW
channels will be red and the LCD will show the following information:
DOLBY DIGITAL CO
BASS CONFIG.3
field
EQ on/off EQ setup
5
P
Bass Config. Off
preset 1
preset 2
preset 3
With this setting, the bass signal below 120Hz will be sent to all
save1
preset 4
load
the speakers; the LEDs on front panel of AEGOP5 indicating
BassManager
Cen
L/R/C/SL/SR/SW channels will be red and the LCD will show the
SL/SR
SW
following information:.
VOL
D Time
DOLBY DIGITAL CO
DRC
BASS CONFIG.OFF
reset
13
ON
OFF
ON