- ページ 2
アクセサリー ABC Spa Cover Removal Universal Spa Cover LifterのPDF 組み立ておよび使用方法をオンラインで閲覧またはダウンロードできます。ABC Spa Cover Removal Universal Spa Cover Lifter 2 ページ。
ページを印刷するU.S. Patent #6,000,072
Directions for
Assembling,
Installing
and Using the
Universal Spa
Cover Lifter
w/spring assist
Your UNIVERSAL Spa Cover Lifter requires
minimal assembly after it is unpackaged.
To assemble and install:
1.
Remove the tape and 1/2" #8 self-drilling screw
from Adjustment Bar B.
2.
Insert Connector Bar A into
Adjustment Bar B and
fasten with the 1/2"
#8 self-drilling screw.
3.
Slide Strap Bracket J into Pivot Bar C and fasten with
a 3/4" #8 self-drilling screw.
Note: Do not loosen
Adjustment Screw K.
E
K
4.
Place Connector Bar A on
the spa cover while sliding
Insert Bar A1 under the spa
cover seam.
5.
While sliding the Adjustment Bar B out of the Pivot Bar C, locate
where you want to mount the UNIVERSAL Spa Cover Lifter on
your spa or deck.
Note: if mounting on deck, brackets F1 and F2
must first be turned 90
6.
End of Main Bar E with Bracket F1 should be fastened to the spa
or deck 26" from the end of the spa using 1-1/4" screws.
Bracket F2 must be mounted as close to Pivot Bracket D as possible
(minimum 6" from Bracket F1 ).
Note: Spa cabinets with little backing or lightweight material
where the UNIVERSAL Cover Lifter is to be fastened
may need to be reinforced in that area.
F1
F2
E
6" min.
26"
Canadian Patent #2,282,012
A
B
E
C
J
(spring detail)
A
A1
o
on Main Bar E.
C
Mounted
on Side
D
of Spa
I
H
G
A
A1
A1
A
To assemble and install (continued):
6a.
If the cover lifter is to be mounted
on the deck, the Mounting Brackets
F1 & F2 must be located so that Main
Bar E is 1" from the side of the spa
cabinet. This distance (1") may vary,
depending on the top trim of spa.
Customers of deck-mounted
UNIVERSAL Cover Lifters can
purchase a Mounting Foot for ease of installation.
7.
Slide Bar G into Bar H.
8.
Make sure that the combined width of
Bars G/H is long enough so each
Adjustment Bar B is parallel to the
side of the spa when attached.
If an adjustment is needed,
J
Bars G/H may be cut so that
the sides are not flaring in
or out. Trim Sleeve I to the same length as the combined length of
Bars G/H. Remove one Adjustment Bar B from the sleeve, then
attach Bars G/H to it. Slide Sleeve I over Bars G/H and re-insert
Adjustment Bar B.
9.
Lock Adjustment Bar B and Pivot Bar C by inserting 1/2" self-
drilling Screws L in the holes provided in Pivot Bar C.
10.
Tighten (by turning clockwise) Adjustment Screw K until you
have the desired tension.
Note: Adjustment Screw K may need to be adjusted periodically
to maintain desired tension.
11.
Insert Wind Pin K into hole #2 of Pivot Bracket D
to lock the UNIVERSAL Spa Cover Lifter in the open
position during use to avoid personal injury.
To move the spa cover off:
1. flip
tel: (604) 856-0275
fax: (604) 556-0244
www.spacoverremover.ca
other Patents applied for
L
C
B
K
E
E
F1
F1
F2
Mounted
on Deck
F1
E
I
G/H
B
2. rotate
3. THAT'S IT!
The cover can be easily moved off
and on from inside the spa.
April/2005
J
L
D
F2
D
K