- ページ 2

レシーバー DKS 8040 microclikのPDF ユーザーマニュアルをオンラインで閲覧またはダウンロードできます。DKS 8040 microclik 3 ページ。 Rf receiver
DKS 8040 microclik にも：ユーザーマニュアル (4 ページ)

ページを印刷する

How Receiver Functions

The 8040 receiver responds to the MicroPLUS or MicroCLIK transmitter's "Transmitter

Code" that is defined by "Transmitter Button Codes" and "Facility Codes". For

example: an 8040 receiver can be programmed to respond to only the first button on a

multiple button MicroPLUS or MicroCLIK transmitter while a second 8040 receiver

can be programmed to respond to only the second button of the same multiple

button MicroPLUS or MicroCLIK transmitter. Thus allowing a single multiple button

MicroPLUS or MicroCLIK transmitter to activate two different receivers without

fear of both receivers responding to the same transmitter code.

In wiegand output mode (Program selector setting 2, 3 or 4), you have the option of

having the receiver match (Program selector setting 5) or ignore (Program selector

setting 6) the facility code to allow the receiver to activate. One receiver can be

programmed to respond to a specific facility code while another receiver can be programmed

for a different facility code.

Programming Selector's 11 positions:

1. Learn Single Transmitter

2. 26-bit Wiegand Mode (Factory Setting)

3. 31-bit Wiegand Mode

4. 30-bit Wiegand Mode

5. Match Facility Code

6. Ignore Facility Code (Factory Setting)

Check if Receiver is set for MicroPLUS or MicroCLIK Mode

1. Turn receiver's power OFF then back ON.

2. Receiver will BEEP twice for MicroCLIK mode. Receiver will BEEP three times for MicroPLUS mode (Factory Setting).

If you need to change the receiver's mode, follow the steps below.

CAUTION:

Changing an EXISTING programmed receiver from one mode to the other will erase ALL EXISTING MEMORY that has been previously

programmed in the receiver. This cannot be UNDONE.

Change Mode (MicroPLUS or MicroCLIK)

1A. Turn the Programming Selector to "Position B" will change to MicroPLUS mode.

1B. Turn the Programming Selector to "Position C" will change to MicroCLIK mode.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once. Press and hold button again, LED will flash

and receiver will beep. Press and hold button a third time until LED continually flashes and beeps.

Note: If receiver does not emit a continuous beep after pressing the button 3 times, try repeating step 2 faster or slower until it does.

3. Turn power OFF, then back ON. Receiver will BEEP twice for MicroCLIK mode (1B) or three times for MicroPLUS mode (1A).

Learn a Single Transmitter for Wiegand Output

Only a single transmitter needs to be programmed (Learned) into the receiver memory. All other transmitters that match the Learned transmitter's

Facility Code and Transmitter Button Code will be output in wiegand format to the access controller.

Important: This programming is for wiegand output to an access controller ONLY and will NOT work when using the Stand-Alone setup (Relay

connection). Low power mode can only be used in Stand-Alone setup.

1. Turn the Programming Selector to Position 1.

2. Press and HOLD Program Button until the Program LED flashes ONCE and receiver will BEEP once. Receiver is now in "Learn Mode" and will

flash and beep for 10 seconds.

3. Press a specific button on the desired transmitter to be "Learned" within 10 seconds, wait for the receiver to time-out.

All desired transmitters with matching facility/button codes will now operate when their button is pressed.

26, 30 or 31-Bit Wiegand Output

The receiver can be changed from the factory set 26-Bit to 30 or 31-Bit wiegand output if desired.

1A. Turn the Programming Selector to "Position 2" will change to 26-Bit Wiegand (Factory Setting).

1B. Turn the Programming Selector to "Position 3" will change to 31-Bit Wiegand.

1C. Turn the Programming Selector to "Position 4" will change to 30-Bit Wiegand.

2. Press and hold Program Button until the Program LED flashes ONCE and receiver will BEEP once.

3. Receiver LED will then give a long flash and beep.

4. This indicates receiver is now changed to "Your Selected Wiegand Bit Size Chosen in Step 1".

8040 065-E-7-14

7. Not Used

8. Low-Power Mode (Stand-Alone Setup ONLY)

9. Normal-Power Mode (Factory Setting)

A. Erase ALL Memory

B. Set Receiver to MicroPLUS Mode (Factory Setting)

C. Set Receiver to MicroCLIK Mode

D-F. Not Used

Program

Selector

Program Button

Program LED: Will flash

sequences during

programming and

flashes during normal

operation or frequency

interference.

Wiegand LED's: Will blink

as wiegand data is being

transmitted.