- ページ 13

高圧洗浄機 Blue Clean AR112のPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。Blue Clean AR112 17 ページ。 Power washer

ページを印刷する

TROUBLESHOOTING AND FAQs

Unit will not turn on.

The high-pressure (HP)

hose will not connect / stay

connected to the spray gun.

Is this a spray gun problem?

The unit is running but there

LV QRW ZDWHU ÀRZ

Why is water leaking where

the high-pressure hose

connects to the spray gun?

I can't remove the lance from

the spray gun. What should

I do?

The power washer turns on

for 2 seconds, shuts off, and

will not turn back on. Do I

have a defective unit?

Make sure the power washer is in the "OFF" position. Plug in

the electrical cord to a grounded 120 volt outlet (no electrical

extension cord should be used). If the electrical cord will

not plug into your outlet, your electrical outlet is not properly

grounded and should not be used. Use another electrical

outlet. Press the reset button on GFCI power box. If the color

of red is not visible in the little window on the GFCI, unplug and

plug in again. Press reset, and look for the red contact. The

color in the window should remain the red color. If the color is

staying red, turn the power switch on the power washer to "ON".

Squeeze the trigger and try again.

If this did not correct the problem, try plugging into another

electrical outlet and repeat the above procedure. If it is still not

working, call Customer Service at 1-866-235-5112.

In most cases, the spray gun is not the problem. The problem

LV WKH UXEEHU VOHHYH FRYHULQJ WKH ¿WWLQJ DW WKH HQG RI WKH KLJK

pressure hose. It has likely slipped up toward the metal tip.

7KH ¿[ ZLJJOH WZLVW DQGRU SXOO WKH UXEEHU VOHHYH GRZQ XQWLO

WKH HQWLUH WLS LV YLVLEOH SOXV DQ ´ RI WKH PHWDO ¿WWLQJ EHORZ WKH

tip. Now try to insert the hose tip into the spray gun. It should

"click" into place and will not come out until the hose is released

by pushing in the lever on the underside of the spray gun. You

may cut away the end of the sleeve with a sharp knife if unable

to move the sleeve down. Be careful not to cut or puncture the

hose.

Check the water source. Unclog the nozzle on the lance. (See

nozzle cleaning instructions under "Cleaning nozzles"). Or

take off the lance and just spray out of the spray gun. This will

indicate if the problem is with the lance.

Make sure there is an o-ring at the end of the metal tip of the

high pressure hose. If no o-ring is present, the connection

between the hose and spray gun will leak. O-Ring Kits are

available online at www.arblueclean.com or call Customer

Service at 1-866-235-5112 to place an order.

The lance and the detergent tank are attached and removed

from the spray gun in the same manner. Insert the quick-

release end of the lance/detergent bottle into the spray gun.

Press the spray gun and lance together (about a 1/8") and turn

clockwise. The lance will lock in place. Remove the lance

by reversing this procedure. Press the spray gun and lance

together and turn counter clockwise. The lance will slide out.

Or, hold the spray gun and lance in an upright position with

WKH QR]]OH HQG RQ WKH ÀRRU 3XVK WKH ZKROH DVVHPEO\ VWUDLJKW

down to loosen the connection, and then follow the removal

process again. You may also spray soapy water or a lubricant in

the area where the lance connects to the spray gun.

,W VRXQGV OLNH \RXU SRZHU ZDVKHU LV ZRUNLQJ MXVW ¿QH :KHQ WKH

water is connected, the accessories are assembled properly,

and the power switch is turned on, the power washer will turn

on for 1 to 2 seconds to prime the pump. Then it automatically

shuts off and waits for the spray gun trigger to be squeezed.

:KHQ WKH WULJJHU LV VTXHH]HG ZDWHU VWDUWV ÀRZLQJ WKURXJK WKH

power washer, the water sensor (TSS) in the pump "senses" the

moving water and automatically turns the power washer pump

on. The water coming out of the spray gun and lance will be

under high pressure. The pump has a Total Stop System (TSS)

ZKLFK PHDQV WKH SXPS ZLOO QRW WXUQ RQ LI WKHUH LV QR ZDWHU ÀRZ

Aim carefully and begin cleaning. Or, turn the power off on the

power washer. Hold the trigger on the spray gun, so you have

a steady stream of water. While holding the trigger on the spray

gun, at the same time, turn the power switch to on.