- ページ 5

ペットケア製品 DogWatch Performance SeriesのPDF オーナーズマニュアルをオンラインで閲覧またはダウンロードできます。DogWatch Performance Series 13 ページ。 Hidden fence systems
DogWatch Performance Series にも：オーナーズマニュアル (14 ページ), インストレーション・マニュアル (10 ページ), オーナーズマニュアル (16 ページ)

ページを印刷する

thicknesses. For single-ply collars, mount the recessed holes of the CollarBone

against the collar strap and for double-ply collars, place the flat side of the

CollarBone against the collar strap. See the illustration on page 5.

Contact Posts: The receiver comes with a set of contact posts. Your DogWatch

Dealer will determine the correct set based on your dog's neck shape, coat, and skin

sensitivity. The posts must make contact with the skin in order for the dog to feel the

correction. In certain cases, your dealer may recommend clipping some of the hair

around the contact posts so that they can touch the skin more easily. Use care if you

find it necessary to tighten the contact posts with the collar wrench, as over-

tightening could cause damage to the receiver.

Antenna: The receiver's omni-directional antenna design assures optimal reception

from the signal field.

Test Light: The test light allows you to test the receiver.

Hold the test light over the contact posts as shown in

Figure 3 and carry the receiver into the signal field a few

feet from the ground. When the receiver picks up the

signal from the boundary wire, the audible warning will

sound and the test light will come on when you enter the

correction zone.

Status Light The light continuously monitors your receiver

and provides these features.

Start-Up

When you first insert the battery into your receiver, the status light will

flash red and green. This indicates that the receiver has started properly. Once

started, the status light will continue to flash green once every 30 seconds

indicating normal operation. In the event that the light does not flash, check the

battery to be sure that it has been inserted properly.

(see Page 4).

Training Level Indicator

When programming the

training level of your receiver, the status light will flash

green in conjunction with audible beeps. The number

of flashes will equal the training level you have chosen.

Signal Field Indicator

When testing the receiver in

the signal field the status light will flash green when the

receiver is in the audible zone and will flash green and

red when the receiver is in the correction zone.

Correction lert

You will be able to tell if your pet

has tested the boundary by looking at the status light.

The status light will double flash green every 30

seconds during the 24-hour period after the dog has

entered the boundary area.

Battery Indicator

This feature monitors the voltage

level of the battery. Once the receiver detects that the

battery has reached a low voltage level, the status light

will change from the normal blinking "green" every 30

seconds to blinking "red" every 10 seconds. This

indicates that your battery is close to the end of its useful life and you should

change the battery within the next 3-4 days.

See page 7 for how to change your battery and reset your receiver.

igure 1

igure 2: R7 Receiver

igure 3: R8 Receiver

Batteries

IMPORTANT: The use of any battery other than a battery authorized by DogWatch Inc. can

cause erratic operation of the Receiver or could cause permanent damage. The use of any

unauthorized battery will void the warranty on the receiver.

Battery Insertion Instructions

R7 Battery: The R7 receiver is powered by a 3 volt (1/3 N) lithium battery. The

receiver is designed for a battery life of up to 6 months. The negative (-) end of the

battery must be inserted down. (Figure 4)

R8 Battery: The R8 battery is powered by a 3.6 volt lithium battery. The receiver is

designed for a battery life of up to two years. The positive (+) end of the battery must

be inserted down. (Figure 5)

Insert R7 battery NEGATIVE end down.

igure 4

Battery Plans

Ask your DogWatch Dealer about a battery plan. If your DogWatch Dealer does not

offer a battery plan, you can join the DogWatch Battery Program, where a new battery

is mailed to you every 6 or 24 months, depending on the type of receiver you own.

Call DogWatch at 800-793-3436 or join through the website at www.dogwatch.com.

Resetting the Battery Indicator on your Receiver

1. Remove the old battery.

2. Using your test light, hold the magnet in the programming position without the

battery in the receiver (see Figures 1 and 2) for five seconds to fully discharge the

unit. If you have misplaced the test light, let the receiver sit for five minutes without

a battery before inserting a new battery.

3. Insert a new battery. The Battery Reminder feature is now automatically reset.

If you forget to discharge your receiver prior to inserting a new battery the Battery

Indicator Feature will automatically reset within the next 24 hours.

Insert R8 battery POSITIVE end down.

igure 5