DogWatch Performance Series Manuel du propriétaire - Page 5
Parcourez en ligne ou téléchargez le pdf Manuel du propriétaire pour {nom_de_la_catégorie} DogWatch Performance Series. DogWatch Performance Series 13 pages. Hidden fence systems
Également pour DogWatch Performance Series : Manuel du propriétaire (14 pages), Manuel d'installation (10 pages), Manuel du propriétaire (16 pages)
Imprimer la page
thicknesses. For single-ply collars, mount the recessed holes of the CollarBone
against the collar strap and for double-ply collars, place the flat side of the
CollarBone against the collar strap. See the illustration on page 5.
Contact Posts: The receiver comes with a set of contact posts. Your DogWatch
Dealer will determine the correct set based on your dog's neck shape, coat, and skin
sensitivity. The posts must make contact with the skin in order for the dog to feel the
correction. In certain cases, your dealer may recommend clipping some of the hair
around the contact posts so that they can touch the skin more easily. Use care if you
find it necessary to tighten the contact posts with the collar wrench, as over-
tightening could cause damage to the receiver.
Antenna: The receiver's omni-directional antenna design assures optimal reception
from the signal field.
Test Light: The test light allows you to test the receiver.
Hold the test light over the contact posts as shown in
Figure 3 and carry the receiver into the signal field a few
feet from the ground. When the receiver picks up the
signal from the boundary wire, the audible warning will
sound and the test light will come on when you enter the
correction zone.
Status Light The light continuously monitors your receiver
and provides these features.
Start-Up
When you first insert the battery into your receiver, the status light will
I
flash red and green. This indicates that the receiver has started properly. Once
started, the status light will continue to flash green once every 30 seconds
indicating normal operation. In the event that the light does not flash, check the
battery to be sure that it has been inserted properly.
(see Page 4).
Training Level Indicator
When programming the
I
training level of your receiver, the status light will flash
green in conjunction with audible beeps. The number
of flashes will equal the training level you have chosen.
Signal Field Indicator
When testing the receiver in
I
the signal field the status light will flash green when the
receiver is in the audible zone and will flash green and
red when the receiver is in the correction zone.
Correction lert
You will be able to tell if your pet
I
has tested the boundary by looking at the status light.
The status light will double flash green every 30
seconds during the 24-hour period after the dog has
entered the boundary area.
Battery Indicator
This feature monitors the voltage
I
level of the battery. Once the receiver detects that the
battery has reached a low voltage level, the status light
will change from the normal blinking "green" every 30
seconds to blinking "red" every 10 seconds. This
indicates that your battery is close to the end of its useful life and you should
change the battery within the next 3-4 days.
See page 7 for how to change your battery and reset your receiver.
igure 1
igure 2: R7 Receiver
igure 3: R8 Receiver
6
Batteries
IMPORTANT: The use of any battery other than a battery authorized by DogWatch Inc. can
cause erratic operation of the Receiver or could cause permanent damage. The use of any
unauthorized battery will void the warranty on the receiver.
Battery Insertion Instructions
R7 Battery: The R7 receiver is powered by a 3 volt (1/3 N) lithium battery. The
receiver is designed for a battery life of up to 6 months. The negative (-) end of the
battery must be inserted down. (Figure 4)
R8 Battery: The R8 battery is powered by a 3.6 volt lithium battery. The receiver is
designed for a battery life of up to two years. The positive (+) end of the battery must
be inserted down. (Figure 5)
Insert R7 battery NEGATIVE end down.
igure 4
Battery Plans
Ask your DogWatch Dealer about a battery plan. If your DogWatch Dealer does not
offer a battery plan, you can join the DogWatch Battery Program, where a new battery
is mailed to you every 6 or 24 months, depending on the type of receiver you own.
Call DogWatch at 800-793-3436 or join through the website at www.dogwatch.com.
Resetting the Battery Indicator on your Receiver
1. Remove the old battery.
2. Using your test light, hold the magnet in the programming position without the
battery in the receiver (see Figures 1 and 2) for five seconds to fully discharge the
unit. If you have misplaced the test light, let the receiver sit for five minutes without
a battery before inserting a new battery.
3. Insert a new battery. The Battery Reminder feature is now automatically reset.
If you forget to discharge your receiver prior to inserting a new battery the Battery
Indicator Feature will automatically reset within the next 24 hours.
Insert R8 battery POSITIVE end down.
igure 5
7