- ページ 6
食器洗い機 Asko D1976CSTMのPDF 取付説明書をオンラインで閲覧またはダウンロードできます。Asko D1976CSTM 14 ページ。 Standard dishwashers
Asko D1976CSTM にも： 取扱説明書 (12 ページ), クイック・スタート・マニュアル (2 ページ), インストールとカスタマイズ (4 ページ), 取扱説明書 (12 ページ)
ページを印刷する
ELECTRICAL CONNECTIONS
WARNING!
Before working on wiring for any
electrical appliance, be sure the electrical power
has been turned off at the breaker/fuse box.
WARNING!
D i s c o n n e c t
supply and place a tag at the disconnect switch
indicating that you are working on the circuit.
WARNING!
E l e c t r i c a l
c o n n e c t i o n s m u s t c o m p l y w i t h t h e a p p l i c a b l e
p o r t i o n s o f t h e n a t i o n a l e l e c t r i c a l c o d e a n d / o r
other local electrical codes.
The dishwasher comes with an electrical
cord for 110-120 volts, 15/20 amp supplied.
This cord should be plugged into the 110-
120 volt outlet under the sink.
If the cord is not long enough, or if a hard-wire
installation is needed, follow instructions on page 7.
GROUNDING INSTRUCTIONS
This unit must be grounded to operate properly. It must
be connected to a grounded metal, permanent wiring
system, or an equipment-grounding conductor must
be run with the circuit conductors and connected to the
equipment-grounding terminal or lead of the appliance.
PREPARING THE DISHWASHER FOR INSTALLATION
At this point the styrofoam, plastic wrap, and the wood
pallet (base) should be removed from the dishwasher.
Now is an excellent time to inspect for any shipping
damage. Should you find any damage, you should
report it to your dealer or builder immediately.
Be sure to remove the toe kick and toe kick insulation
which are wrapped in heavy brown paper and packed
inside or on top of the dishwasher.
SLIDES FOR REAR LEGS
The unit comes with two white plastic slides for the rear
legs to protect the kitchen floor from being damaged
when you slide the unit into place. The slides simply
snap onto the bottom of the rear legs.
Protective slides for rear
legs simply snap onto the
bottom of the legs.
REMOVING THE ACCESS PANEL
To remove the access panel, first remove the two screws
on each side of the access panel that hold the fill strips
in place. (NOTE: Do not replace these screws.) Next,
remove the two screws underneath the panel that hold
it against the guard plate.
After you have removed all four screws, slide the access
panel down below the two tabs at the top to remove it.
NOTE:
When you replace the panel, be sure to replace
only the screws that attach it to the guard plate.
Page 6
e l e c t r i c a l
p o w e r
a n d
g r o u n d i n g
WARNING!
Do not use an extension cord for this appliance.
NOTE: Access holes should be 1-1/2" to 2" (38 mm
to 50 mm) in diameter with no sharp edges.
Damage to the dishwasher could occur if it is not
properly grounded.
WARNING! Make sure the water supply line,
drain line and branch circuit wiring do not touch
any exposed terminals of dishwasher wiring.
THE FILL STRIPS
All standard ASKO dishwashers (Models D1706, D1716,
D1776, D1876, D1976) have color-coded fill strips to
finish off the installation. To prevent damage to the
machine, be sure to remove the shipping screws that
secure the fill strips to the access panel. These
screws are to be thrown away. Do not replace them
into the access panel.
Lower Access Panel
If the cabinet opening is European measure-
NOTE:
ment (23-1/2 inches [597 mm]), remove the fill
strips to fit the dishwasher into the opening.
WARNING!
Do not screw the fill
strips back to the
lower access panel;
otherwise, the
machine will have to
be uninstalled if
service is necessary.
Fill Strip