タイマー Ambient NanoLockitのPDF クイック・スタート・マニュアルをオンラインで閲覧またはダウンロードできます。Ambient NanoLockit 2 ページ。 Timecode + logging
Ambient NanoLockit にも： クイック・スタート・マニュアル (2 ページ), クイック・スタートアップ・マニュアル (20 ページ), クイック・スタート・マニュアル (5 ページ), マニュアル (4 ページ), チュートリアル (5 ページ), クイックマニュアル (2 ページ), マニュアル (19 ページ)
ページを印刷する
Lockit
Nano
QUICK START GUIDE
Status LED
Lemo Connector:
TC (and metadata)
interface
Micro USB:
charge and external
Green Button
power
Red Button
Charge time
Power Button
15 min
30 min
2 hrs
LED status overview
Status LED Codes
short
ext. power, idle, charging
long
ext. power, idle, fully charged
int. power, lo bat
Generator Mode:
idle, no TC out, RTC lost
idle, no TC out, RTC OK
generator set, TC out
generator set, TC out, lo bat*
generator set, TC level reduced
TRX Mode:
idle, no TC on input or ACN
TX (LTC/MTC via cable)
RX (LTC/MTC over ACN)
*ca. 30 min left
Example setup
TC IN
NANOLOCKIT
TC OUT
Audio Recorder
NANOLOCKIT
DSLR Camera
NANOLOCKIT
Film Camera
*NOTE: The specific cable required is dependent on the connected device. The most common cables
are: TC-IO-35RA, TC-IO, LTC-Out, LTC-Out/Epic. Please check our website.
1
Turn on all NanoLockits
ACN Antenna:
Press the Power Button on all
for wireless sync with
NanoLockits for 3 seconds until the
other Lockits
LED lights up green . Then release
and LEDs start to flash.
Operation
5 hrs
10 hrs
NOTE: To reset the unit to factory default, start by holding the
35 hrs (full)
Power Button for 10 seconds until LED lights up red
1 sec
2 sec
The NanoLockit starts up with muted output at last
selected frame rate (default 25 fps).
To activate the LEMO Output and to jam other
Lockits with the internal Real Time Clock (RTC),
proceed with step 3.
To adjust the RTC and frame rate, proceed with step
2A. To jam from an external device, proceed with
step 2B.
The goal: syncing timecode (TC) and frame rate (FPS).
TC 01:23:45:12
Timecode Cable*
TC 01:23:45:12
TC-IO-35RA
(included)
TC 01:23:45:12
Timecode Cable*
3 sec
.
TC
FPS
2A
Set the internal clock of the NanoLockit
To set the RTC and the
frame rate, use the Lockit-
Toolbox software (PC and
Mac, available at nanolo-
ckit.com).
NOTE: On start a valid RTC will be indicated by
LEDs flashing red/green
, a lost RTC by flas-
hing red
.
2B
Set the internal clock of the NanoLockit
To jam your NanoLockit from an
external device, connect it with
the appropriate timecode cable.
If successful, the LED will flash
green
. Finish by disconnec-
ting the cable.
External jamming sets the TC and FPS
while activating the LEMO output.
3
Set and jam from internal RTC
Press the Green Button for 3
seconds until LED double blinks
green:
.
This sets the TC and FPS, wire-
lessly syncs all other NanoLockits,
12:45:12:02
25 fps
and activates all LEMO outputs.
If successful, all units will flash
green
in sync.
LockitToolbox
RTC
micro USB
TC 01:23:45:12
25 fps
TC
FPS
TC IN
NANOLOCKIT
TC OUT
TC & FPS
3 sec