Coastal MYGIG LOCKPICK PRO 설치 및 작동 지침 매뉴얼 - 페이지 6

{카테고리_이름} Coastal MYGIG LOCKPICK PRO에 대한 설치 및 작동 지침 매뉴얼을 온라인으로 검색하거나 PDF를 다운로드하세요. Coastal MYGIG LOCKPICK PRO 15 페이지. Adapter for chrysler/dodge/jeep

페이지 인쇄

Coastal MYGIG LOCKPICK PRO 설치 및 작동 지침 매뉴얼

On the back of a MYGIG radio may be additional

equipped, there will be a BLUE connection for the GPS antenna. A GPS antenna is necessary for

navigation equipped MYGIG radios to provide map and route guidance. If you did not receive one with

your new radio, they are available at your local Chrysler/Dodge/Jeep dealer or online from several

sources. GPS antennas can be installed directly on top of the radio or further back inside the dash as

long as there is not substantial metal blocking reception from above. Also, your radio may have a TAN

connector for attachment of a Sirius Radio antenna. The MYGIG radio is designed with an internal

Sirius satellite radio tuner built in so all you need is an antenna for satellite radio reception. If your

vehicle already had a separate Sirius tuner, it is not used or compatible with the MYGIG which already

contains one internally.

and Bluetooth Uconnect phone use will be active. Plug in a MYGIG microphone to the 10 pin connector

present on the rear of your MYGIG radio and place the microphone in a convenient location.

Microphones are available from your local dealer, or aftermarket solutions are available online.

Plug in any multimedia video or audio desired at this time to your

RCA connections for Video and Audio inputs. Also labeled on your cable are standard RCA connections

for Video and Audio outputs.

If your original radio was a navigation radio equipped with a rear view camera, your radio had a 3 pin

white connector plugged in.

off and replace it with an RCA connector to plug into the MYGIG camera input provided on the

multimedia harness. The center wire is video signal and the outside wires are ground and can be

connected together. If you would like to view your present camera while in DRIVE or other gears, the

included REVERSE CAMERA POWER output wire must be connected as the power source for your

camera. This 12V power output will turn on when the vehicle is placed in reverse and also when selected

by the user using the radio buttons. Currently, your factory camera is powered from the reverse taillight

source. This power is only present while you are in reverse.

If you choose not to connect the REVERSE CAMERA POWER wire provided by the Lockpick

harness to your factory rear camera, the rear camera view while backing up will continue working as

normal. However, because the rear camera will have no power in other gears, it cannot be activated by

the Lockpick and will display as a blank or flashing picture if activated manually while in Drive.

Installation of the REVERSE CAMERA POWER wire to enable factory camera operation in all

gears

is simply a matter of running a wire to the factory camera and connecting it in place of the original

power wire. Remove any panels covering the rear hatch in your vehicle. Then use a meter or indicator

lamp to determine the reverse power connection on the factory camera connector. Make sure you are

measuring directly on the connector at the camera location and not further back in a different location.

This wire will switch to 12V while the vehicle is in REVERSE and will be zero at other times. Then cut

this wire and connect the REVERSE CAM 12V+ power connection from the Lockpick to the camera

directly. Do not reconnect the original camera power source wire or fail to cut the wire at the camera.

Instead tape it up and disregard it. The Lockpick will provide all necessary power and timing for the

factory camera. Failing to cut the wire or connecting the Lockpick power and factory power at the same

time could cause the reverse tail light to illuminate at improper times. Also, cutting the wire at a different

location other than directly on the camera connector could possibly interrupt power to other functions

such as the actual reverse taillights or rear obstacle detection systems.

If you do not currently have a rear view camera and want to add one to your vehicle, the Lockpick

makes it easy.

The REVERSE CAM 12V + power output provided on the Lockpick will be your source

for powering the 12V needs of your aftermarket rear camera. Also, a GROUND connection is already

provided for you on the Lockpick harness to make powering your camera simple.

The Lockpick includes the option for a 2

the back of a trailer automatically while in reverse. Plug your camera into the 2

input and the camera power to the REVERSE CAMERA 12V power and GROUND connection on the

Lockpick harness.

Also, if your radio is navigation

If you would like to continue using your present camera, cut the connector

Reverse camera (CARGO CAM)

connectors. If your MYGIG radio is navigation

equipped, the functions for voice recognition

harness. On your cable are standard

for viewing of a truck bed or

REVERSE CAMERA